Archives
Info Inbox
info@turnpack.com
-
RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs
For sure! I’ll send a couple in the box for you to test. But yeah, I tried several of our toolholders on an older jig and a newer jig and they all showed the same issues.
I include an older jig as well (labeled) so you can compare to that as well. I’ll try to get this over and shipped out tomorrow!
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 27, 2026 4:45 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
Not good, but we'll fix them no problem. We have tool holders here and tested them. The only thing I can think of is that ours are on the lower end of the diameter tolerance and yours are on the upper end. Either way send them back and we'll open them up by 130um. Can you also spare one of your toolholders to ensure we are good before returning them to you?
Chris
On Wed, May 27, 2026 at 4:35 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Sweet!
The other item that is more of a concern is that the holes that the tools sit inside of are basically the EXACT size of the tool holders themselves. I can pick up the tools in and out okay, but I have to push (with some decent force) each of the tools into the holes to fully seat them on the holder. I compared with the previous order of the tooling jigs and the tools are much easier to put into the holes and need zero force to sit correctly.
I attached a picture of the measurements I took of the holes in slot 7 on both jigs. The new order of jigs is ~130um smaller which is likely causing the seating issue. We will have a high risk of bending, rotating, or otherwise damaging the tools so we are not comfortable using these as is.
If I were to send all the jigs back, would you be able to machine a slightly larger hole? I can send a jig from a previous order to you or send an empty tool holder for you to test yourself if that helps, or I can take additional measurements as needed. We will have a high risk of bending, rotating, or otherwise damaging the tools so we are not comfortable using these as is. I definitely already rotated one of the tools as I was attempting to pull it off of the jig by hand ☹ Let me know!
Thanks!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 27, 2026 2:55 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
Thanks for the update. You are correct that the set screws are adjustable to account for general tolerances of the toolbank assemblies within the machine. There are set screws for the left, right, and height adjustments. I'd suggest you dial in one and then match all the others; chances are they'll be very close. Let us know if you have any other questions.
Chris
On Wed, May 27, 2026 at 2:50 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
I looked at a few loading jigs, and testing them had some issues. I just found that the screws on either end was obstructing the loading, but I can just twist them more to fit. Each of the jigs have them twisted and sticking out at different lengths though. Is there a specific length they should be? Or should I just size them to slide easily in and out of the tool holders?
Just want to make sure these screws are for any other reason than easy loading/aligning to the tool holder itself 😊. I’ll go through the rest of them either today or tomorrow and let you know if I encounter any more issues.
Once I verify the other jigs are good to go, I’ll send the adapters back and shoot over the tracking number for you.Thanks!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 27, 2026 10:46 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
Sorry about that. We do check them for flatness and vacuum seal so it would be best if you can ship them back for RCA and we'll fix it. Hope this doesn't delay your project.
Any issues with the Loading Jigs?
Chris
On Wed, May 27, 2026 at 10:34 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Hi Chris,
I went through the rest of the delivery and found 3 more that do not slide all the way into the tool (for a total of 4x). Physically they look similar, but may have some slight warpage issues causing these issues. Any ideas on how to fix this? I’m afraid of trying to bend them to fix the warpage. Would you like me to ship them back for you to take a look?
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Garrett Davidson
Sent: Wednesday, May 27, 2026 8:04 AM
To: Christopher Berger <cberger@turnpack.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsSorry, these are two SEPARATE adapters. I’m going through the other adapters now, and will let you know if I see any more issues!
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 27, 2026 7:58 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
Thanks for the info. My fault on the partially engraved one, I was supposed to let you know but fell behind. We already have a replacement for that one in queue but I wanted to ship all 20 just in case you needed the full qty right away. Is this the same adapter you are having the issue with on the suction cup or is this a different one?
Chris
On Wed, May 27, 2026 at 7:50 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Unsure if this sent or if the full email did not send. I received a bunch of error messages.
Please find the video up in the fileXchange if you need!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Garrett Davidson
Sent: Tuesday, May 26, 2026 6:28 PM
To: 'Lorena Carrillo' <lcarrillo@turnpack.com>; 'Christopher Berger' <cberger@turnpack.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Chris/Turnpack,
I started opening up the box, and found an issue with one of the adapters:
As I slide the adapter into our tool, it stops here and does not allow us to slide it all the way to the vacuum port. The adapter itself seemed warped when placed on an optical table. I checked 5 more so far from the latest shipment and they all look good! Just this one is unable to slide in. I attached a video of myself trying to push it it and it not going all the way in without me having to physically lift the adapter into place and have a high risk of “confetti-ing” components in waffle packs. Let me know if it doesn’t come through. I also uploaded into our FileXchange system for you to review. Let me know if anyone needs access to this:
One of the 5 that I looked at after this one is missing most of the writing at the bottom of the adapter itself. Not a huge deal as it’s just cosmetic to us, but did want to let you know about it:
I will go through all the rest tomorrow morning and let you know if I encounter any more like this.
Can I send this one back to you to root cause or any ideas how to fix up? I could try to bend it but unsure how brittle the adapter itself is or if I’ll make it worse.
Thanks!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Garrett Davidson
Sent: Wednesday, May 20, 2026 4:23 PM
To: Lorena Carrillo <lcarrillo@turnpack.com>; 'Christopher Berger' <cberger@turnpack.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsThank you!!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Lorena Carrillo <lcarrillo@turnpack.com>
Sent: Wednesday, May 20, 2026 4:20 PM
To: 'Christopher Berger' <cberger@turnpack.com>; Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHello Team, the order has shipped complete today. Here is your tracking number for reference. 872056271057
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, May 19, 2026 11:18 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
We have the adapters back from anodizing but I slightly underestimated the assembly time. We are wrapping up the assembly today and tomorrow will be for engraving and testing and then we'll ship them out tomorrow.
The toolholder jigs are complete and ready to go.
Thanks
Chris
On Mon, May 18, 2026 at 4:29 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Hey Chris,
Were you able to ship out those parts? And have a tracking number if possible?
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 13, 2026 7:55 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsGarrett,
We experienced a slight delay because a machine was down, but parts are currently at anodizing. We are expediting that process, and then we anticipate two days for post-anodizing assembly & engraving. We might be able to ship it out Saturday, worst case it'll be Monday. I'll keep you posted when the parts come back from anodizing and then I should be able to confirm actual ship date.
Chris
On Wed, May 13, 2026 at 7:39 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Hey Chris,
Just checking if you think you’d be able to ship anything this week?
Thanks!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 4:54 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsPerfect. Thanks for confirming
On Tue, Apr 28, 2026 at 4:44 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Yeah that’s okay with me!
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 4:23 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsGarrett,
Yes. Example image below shows one side machined and the top not machined. If we machine all 4 sides they will all look like the side edge in the image below. Also, we did start with the adapters, once they are ready and in case the jigs are not I will let you know and we can do a partial shipment.
Thanks
Chris
On Tue, Apr 28, 2026 at 4:18 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Sorry, what do you mean by “Obscuring them”? would it “fog” the glass or make it not transparent?
The wafer pack adapters are a higher priority for us if possible! But no worries either way.
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 3:44 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
Making good progress. As of now it looks like we'll ship the order the week of 05/11. We had a question about the tool holder jigs. We would prefer to machine them on multiple sides but doing so would obscure them. Reason being is that the stock material has significant tolerancing, so facing all sides would ensure greater consistency. Any objections to that?
Chris
On Tue, Apr 28, 2026 at 2:54 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Hey Chris,
Hope you are doing well! Do you have an ETA for this order? (PO#3714362)
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Chris Berger <info@turnpack.com>
Sent: Tuesday, April 7, 2026 9:03 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Subject: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett, Attached is the quote for the adapters and loading jigs. Let me know if you need anything else. Chris Christopher Berger Phone: +1 [...] ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏
SO26141038
$ 69,200.00
Expires on 05/07/2026
Hi Garrett,
Attached is the quote for the adapters and loading jigs. Let me know if you need anything else.
Chris
Christopher BergerTurnpack — Efficiency Redefined Through Automation
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
by Garrett Davidson - 07:56 - 27 May 2026 -
Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs
Hi Garrett,Not good, but we'll fix them no problem. We have tool holders here and tested them. The only thing I can think of is that ours are on the lower end of the diameter tolerance and yours are on the upper end. Either way send them back and we'll open them up by 130um. Can you also spare one of your toolholders to ensure we are good before returning them to you?ChrisOn Wed, May 27, 2026 at 4:35 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:Sweet!
The other item that is more of a concern is that the holes that the tools sit inside of are basically the EXACT size of the tool holders themselves. I can pick up the tools in and out okay, but I have to push (with some decent force) each of the tools into the holes to fully seat them on the holder. I compared with the previous order of the tooling jigs and the tools are much easier to put into the holes and need zero force to sit correctly.
I attached a picture of the measurements I took of the holes in slot 7 on both jigs. The new order of jigs is ~130um smaller which is likely causing the seating issue. We will have a high risk of bending, rotating, or otherwise damaging the tools so we are not comfortable using these as is.
If I were to send all the jigs back, would you be able to machine a slightly larger hole? I can send a jig from a previous order to you or send an empty tool holder for you to test yourself if that helps, or I can take additional measurements as needed. We will have a high risk of bending, rotating, or otherwise damaging the tools so we are not comfortable using these as is. I definitely already rotated one of the tools as I was attempting to pull it off of the jig by hand ☹ Let me know!
Thanks!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 27, 2026 2:55 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
Thanks for the update. You are correct that the set screws are adjustable to account for general tolerances of the toolbank assemblies within the machine. There are set screws for the left, right, and height adjustments. I'd suggest you dial in one and then match all the others; chances are they'll be very close. Let us know if you have any other questions.
Chris
On Wed, May 27, 2026 at 2:50 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
I looked at a few loading jigs, and testing them had some issues. I just found that the screws on either end was obstructing the loading, but I can just twist them more to fit. Each of the jigs have them twisted and sticking out at different lengths though. Is there a specific length they should be? Or should I just size them to slide easily in and out of the tool holders?
Just want to make sure these screws are for any other reason than easy loading/aligning to the tool holder itself 😊. I’ll go through the rest of them either today or tomorrow and let you know if I encounter any more issues.
Once I verify the other jigs are good to go, I’ll send the adapters back and shoot over the tracking number for you.Thanks!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 27, 2026 10:46 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
Sorry about that. We do check them for flatness and vacuum seal so it would be best if you can ship them back for RCA and we'll fix it. Hope this doesn't delay your project.
Any issues with the Loading Jigs?
Chris
On Wed, May 27, 2026 at 10:34 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Hi Chris,
I went through the rest of the delivery and found 3 more that do not slide all the way into the tool (for a total of 4x). Physically they look similar, but may have some slight warpage issues causing these issues. Any ideas on how to fix this? I’m afraid of trying to bend them to fix the warpage. Would you like me to ship them back for you to take a look?
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Garrett Davidson
Sent: Wednesday, May 27, 2026 8:04 AM
To: Christopher Berger <cberger@turnpack.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsSorry, these are two SEPARATE adapters. I’m going through the other adapters now, and will let you know if I see any more issues!
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 27, 2026 7:58 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
Thanks for the info. My fault on the partially engraved one, I was supposed to let you know but fell behind. We already have a replacement for that one in queue but I wanted to ship all 20 just in case you needed the full qty right away. Is this the same adapter you are having the issue with on the suction cup or is this a different one?
Chris
On Wed, May 27, 2026 at 7:50 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Unsure if this sent or if the full email did not send. I received a bunch of error messages.
Please find the video up in the fileXchange if you need!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Garrett Davidson
Sent: Tuesday, May 26, 2026 6:28 PM
To: 'Lorena Carrillo' <lcarrillo@turnpack.com>; 'Christopher Berger' <cberger@turnpack.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Chris/Turnpack,
I started opening up the box, and found an issue with one of the adapters:
As I slide the adapter into our tool, it stops here and does not allow us to slide it all the way to the vacuum port. The adapter itself seemed warped when placed on an optical table. I checked 5 more so far from the latest shipment and they all look good! Just this one is unable to slide in. I attached a video of myself trying to push it it and it not going all the way in without me having to physically lift the adapter into place and have a high risk of “confetti-ing” components in waffle packs. Let me know if it doesn’t come through. I also uploaded into our FileXchange system for you to review. Let me know if anyone needs access to this:
One of the 5 that I looked at after this one is missing most of the writing at the bottom of the adapter itself. Not a huge deal as it’s just cosmetic to us, but did want to let you know about it:
I will go through all the rest tomorrow morning and let you know if I encounter any more like this.
Can I send this one back to you to root cause or any ideas how to fix up? I could try to bend it but unsure how brittle the adapter itself is or if I’ll make it worse.
Thanks!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Garrett Davidson
Sent: Wednesday, May 20, 2026 4:23 PM
To: Lorena Carrillo <lcarrillo@turnpack.com>; 'Christopher Berger' <cberger@turnpack.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsThank you!!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Lorena Carrillo <lcarrillo@turnpack.com>
Sent: Wednesday, May 20, 2026 4:20 PM
To: 'Christopher Berger' <cberger@turnpack.com>; Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHello Team, the order has shipped complete today. Here is your tracking number for reference. 872056271057
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, May 19, 2026 11:18 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
We have the adapters back from anodizing but I slightly underestimated the assembly time. We are wrapping up the assembly today and tomorrow will be for engraving and testing and then we'll ship them out tomorrow.
The toolholder jigs are complete and ready to go.
Thanks
Chris
On Mon, May 18, 2026 at 4:29 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Hey Chris,
Were you able to ship out those parts? And have a tracking number if possible?
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 13, 2026 7:55 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsGarrett,
We experienced a slight delay because a machine was down, but parts are currently at anodizing. We are expediting that process, and then we anticipate two days for post-anodizing assembly & engraving. We might be able to ship it out Saturday, worst case it'll be Monday. I'll keep you posted when the parts come back from anodizing and then I should be able to confirm actual ship date.
Chris
On Wed, May 13, 2026 at 7:39 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Hey Chris,
Just checking if you think you’d be able to ship anything this week?
Thanks!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 4:54 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsPerfect. Thanks for confirming
On Tue, Apr 28, 2026 at 4:44 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Yeah that’s okay with me!
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 4:23 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsGarrett,
Yes. Example image below shows one side machined and the top not machined. If we machine all 4 sides they will all look like the side edge in the image below. Also, we did start with the adapters, once they are ready and in case the jigs are not I will let you know and we can do a partial shipment.
Thanks
Chris
On Tue, Apr 28, 2026 at 4:18 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Sorry, what do you mean by “Obscuring them”? would it “fog” the glass or make it not transparent?
The wafer pack adapters are a higher priority for us if possible! But no worries either way.
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 3:44 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
Making good progress. As of now it looks like we'll ship the order the week of 05/11. We had a question about the tool holder jigs. We would prefer to machine them on multiple sides but doing so would obscure them. Reason being is that the stock material has significant tolerancing, so facing all sides would ensure greater consistency. Any objections to that?
Chris
On Tue, Apr 28, 2026 at 2:54 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Hey Chris,
Hope you are doing well! Do you have an ETA for this order? (PO#3714362)
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Chris Berger <info@turnpack.com>
Sent: Tuesday, April 7, 2026 9:03 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Subject: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett, Attached is the quote for the adapters and loading jigs. Let me know if you need anything else. Chris Christopher Berger Phone: +1 [...] ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏
SO26141038
$ 69,200.00
Expires on 05/07/2026
Hi Garrett,
Attached is the quote for the adapters and loading jigs. Let me know if you need anything else.
Chris
Christopher BergerTurnpack — Efficiency Redefined Through Automation
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--Christopher Berger
by Chris Berger - 07:46 - 27 May 2026 -
RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs
Sweet!
The other item that is more of a concern is that the holes that the tools sit inside of are basically the EXACT size of the tool holders themselves. I can pick up the tools in and out okay, but I have to push (with some decent force) each of the tools into the holes to fully seat them on the holder. I compared with the previous order of the tooling jigs and the tools are much easier to put into the holes and need zero force to sit correctly.
I attached a picture of the measurements I took of the holes in slot 7 on both jigs. The new order of jigs is ~130um smaller which is likely causing the seating issue. We will have a high risk of bending, rotating, or otherwise damaging the tools so we are not comfortable using these as is.
If I were to send all the jigs back, would you be able to machine a slightly larger hole? I can send a jig from a previous order to you or send an empty tool holder for you to test yourself if that helps, or I can take additional measurements as needed. We will have a high risk of bending, rotating, or otherwise damaging the tools so we are not comfortable using these as is. I definitely already rotated one of the tools as I was attempting to pull it off of the jig by hand ☹ Let me know!
Thanks!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 27, 2026 2:55 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
Thanks for the update. You are correct that the set screws are adjustable to account for general tolerances of the toolbank assemblies within the machine. There are set screws for the left, right, and height adjustments. I'd suggest you dial in one and then match all the others; chances are they'll be very close. Let us know if you have any other questions.
Chris
On Wed, May 27, 2026 at 2:50 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
I looked at a few loading jigs, and testing them had some issues. I just found that the screws on either end was obstructing the loading, but I can just twist them more to fit. Each of the jigs have them twisted and sticking out at different lengths though. Is there a specific length they should be? Or should I just size them to slide easily in and out of the tool holders?
Just want to make sure these screws are for any other reason than easy loading/aligning to the tool holder itself 😊. I’ll go through the rest of them either today or tomorrow and let you know if I encounter any more issues.
Once I verify the other jigs are good to go, I’ll send the adapters back and shoot over the tracking number for you.Thanks!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 27, 2026 10:46 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
Sorry about that. We do check them for flatness and vacuum seal so it would be best if you can ship them back for RCA and we'll fix it. Hope this doesn't delay your project.
Any issues with the Loading Jigs?
Chris
On Wed, May 27, 2026 at 10:34 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Hi Chris,
I went through the rest of the delivery and found 3 more that do not slide all the way into the tool (for a total of 4x). Physically they look similar, but may have some slight warpage issues causing these issues. Any ideas on how to fix this? I’m afraid of trying to bend them to fix the warpage. Would you like me to ship them back for you to take a look?
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Garrett Davidson
Sent: Wednesday, May 27, 2026 8:04 AM
To: Christopher Berger <cberger@turnpack.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsSorry, these are two SEPARATE adapters. I’m going through the other adapters now, and will let you know if I see any more issues!
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 27, 2026 7:58 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
Thanks for the info. My fault on the partially engraved one, I was supposed to let you know but fell behind. We already have a replacement for that one in queue but I wanted to ship all 20 just in case you needed the full qty right away. Is this the same adapter you are having the issue with on the suction cup or is this a different one?
Chris
On Wed, May 27, 2026 at 7:50 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Unsure if this sent or if the full email did not send. I received a bunch of error messages.
Please find the video up in the fileXchange if you need!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Garrett Davidson
Sent: Tuesday, May 26, 2026 6:28 PM
To: 'Lorena Carrillo' <lcarrillo@turnpack.com>; 'Christopher Berger' <cberger@turnpack.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Chris/Turnpack,
I started opening up the box, and found an issue with one of the adapters:
As I slide the adapter into our tool, it stops here and does not allow us to slide it all the way to the vacuum port. The adapter itself seemed warped when placed on an optical table. I checked 5 more so far from the latest shipment and they all look good! Just this one is unable to slide in. I attached a video of myself trying to push it it and it not going all the way in without me having to physically lift the adapter into place and have a high risk of “confetti-ing” components in waffle packs. Let me know if it doesn’t come through. I also uploaded into our FileXchange system for you to review. Let me know if anyone needs access to this:
One of the 5 that I looked at after this one is missing most of the writing at the bottom of the adapter itself. Not a huge deal as it’s just cosmetic to us, but did want to let you know about it:
I will go through all the rest tomorrow morning and let you know if I encounter any more like this.
Can I send this one back to you to root cause or any ideas how to fix up? I could try to bend it but unsure how brittle the adapter itself is or if I’ll make it worse.
Thanks!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Garrett Davidson
Sent: Wednesday, May 20, 2026 4:23 PM
To: Lorena Carrillo <lcarrillo@turnpack.com>; 'Christopher Berger' <cberger@turnpack.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsThank you!!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Lorena Carrillo <lcarrillo@turnpack.com>
Sent: Wednesday, May 20, 2026 4:20 PM
To: 'Christopher Berger' <cberger@turnpack.com>; Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHello Team, the order has shipped complete today. Here is your tracking number for reference. 872056271057
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, May 19, 2026 11:18 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
We have the adapters back from anodizing but I slightly underestimated the assembly time. We are wrapping up the assembly today and tomorrow will be for engraving and testing and then we'll ship them out tomorrow.
The toolholder jigs are complete and ready to go.
Thanks
Chris
On Mon, May 18, 2026 at 4:29 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Hey Chris,
Were you able to ship out those parts? And have a tracking number if possible?
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 13, 2026 7:55 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsGarrett,
We experienced a slight delay because a machine was down, but parts are currently at anodizing. We are expediting that process, and then we anticipate two days for post-anodizing assembly & engraving. We might be able to ship it out Saturday, worst case it'll be Monday. I'll keep you posted when the parts come back from anodizing and then I should be able to confirm actual ship date.
Chris
On Wed, May 13, 2026 at 7:39 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Hey Chris,
Just checking if you think you’d be able to ship anything this week?
Thanks!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 4:54 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsPerfect. Thanks for confirming
On Tue, Apr 28, 2026 at 4:44 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Yeah that’s okay with me!
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 4:23 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsGarrett,
Yes. Example image below shows one side machined and the top not machined. If we machine all 4 sides they will all look like the side edge in the image below. Also, we did start with the adapters, once they are ready and in case the jigs are not I will let you know and we can do a partial shipment.
Thanks
Chris
On Tue, Apr 28, 2026 at 4:18 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Sorry, what do you mean by “Obscuring them”? would it “fog” the glass or make it not transparent?
The wafer pack adapters are a higher priority for us if possible! But no worries either way.
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 3:44 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
Making good progress. As of now it looks like we'll ship the order the week of 05/11. We had a question about the tool holder jigs. We would prefer to machine them on multiple sides but doing so would obscure them. Reason being is that the stock material has significant tolerancing, so facing all sides would ensure greater consistency. Any objections to that?
Chris
On Tue, Apr 28, 2026 at 2:54 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Hey Chris,
Hope you are doing well! Do you have an ETA for this order? (PO#3714362)
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Chris Berger <info@turnpack.com>
Sent: Tuesday, April 7, 2026 9:03 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Subject: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett, Attached is the quote for the adapters and loading jigs. Let me know if you need anything else. Chris Christopher Berger Phone: +1 [...] ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏
SO26141038
$ 69,200.00
Expires on 05/07/2026
Hi Garrett,
Attached is the quote for the adapters and loading jigs. Let me know if you need anything else.
Chris
Christopher BergerTurnpack — Efficiency Redefined Through Automation
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
by Garrett Davidson - 07:37 - 27 May 2026 -
Re: RFQ
Tony,That works for us! I'll get with Lorena on getting these ordered.
Thank you for your time.Best,IvanOn Wed, May 27, 2026 at 2:19 PM Tony Haynes <thaynes@flodraulicgroup.com> wrote:Hi Ivan,
We can square them; quote and lead time are the same. Let me know if that is satisfactory.
Best Regards,
Tony Haynes
Technical Sales Representative
FLODRAULIC
Cell 480.997.2852
Fax 480.921.3272
1150 N. FIESTA BLVD. GILBERT, AZ 85233
ISO 9001:2015 Registered
*** Important Notice: Send all Inquiries/Orders to our new Customer Service email address SWSales@flodraulicgroup.com***
From: Ivan Arevalo <iarevalo@turnpack.com>
Sent: Wednesday, May 27, 2026 9:49 AM
To: Tony Haynes <thaynes@flodraulicgroup.com>
Cc: Brandon Benavidez <bbenavidez@turnpack.com>; Christopher Berger <cberger@turnpack.com>; Info at Turnpack <info@turnpack.com>
Subject: Re: RFQ
Hi Tony,
Yes, please square those up so we can get the caps on.
I'll get with Chris and Brandon to determine how we want to move forward.
Thanks,
Ivan
On Tue, May 26, 2026 at 10:57 AM Tony Haynes <thaynes@flodraulicgroup.com> wrote:Hi Ivan,
Here is the Simple Side Module Enclosure quote project number 26359M1 for Turnpack.We aligned the frames and connectors for the simple side module. Please review
Cost for Kit: $2,243.90 each
Cost for Assembled: $2,809.61 each
5-7 Days
Here is the base module top enclosure quote project number 26358M1 for Turnpack.*****The bars you want cover caps on are not square on the end so will not go on.
*****If you want them squared, we can square them up and then add the end caps.
Cost for Kit: $1,012.17 each
Cost for Assembled: $1,272.10 each
5-7 Days
Best Regards,Tony Haynes
Technical Sales Representative
FLODRAULIC
Cell 480.997.2852
Fax 480.921.3272
1150 N. FIESTA BLVD. GILBERT, AZ 85233
ISO 9001:2015 Registered
*** Important Notice: Send all Inquiries/Orders to our new Customer Service email address SWSales@flodraulicgroup.com***
From: Ivan Arevalo <iarevalo@turnpack.com>
Sent: Thursday, May 21, 2026 5:41 PM
To: Tony Haynes <thaynes@flodraulicgroup.com>
Cc: Brandon Benavidez <bbenavidez@turnpack.com>; Christopher Berger <cberger@turnpack.com>; Info at Turnpack <info@turnpack.com>
Subject: RFQ
Hi Tony,
I've attached two .scene files for some extrusions that we would like pricing on below.
The Base Module Top Enclosure should have the flat edge of the 40x80 3E facing outward. In MAYCAD, it shows up red as an error but we just want the slotted sides to be facing inward toward the enclosure. Additionally, I couldn't get the rubber caps onto the ends of the angled top extrusions in MAYCAD, but we want rubber caps on those.
For the Simple Side Module Enclosure, do not quote the two "hurdles" that connect the back of the enclosure and the front 120x40 extrusion. Those are just placeholders to properly render the mating connection points. We also need additional mounting locations along the front extrusion for better support due to the extended length.
Please reach out with any questions or concerns.
Thank you for your assistance.
Best,Ivan
by Ivan Arevalo - 07:16 - 27 May 2026 -
Your Xometry Order 4166D-15010 has been delivered.
Your order has been delivered.Your shipment from Xometry has arrived.
Wednesday, May. 27, 2026 at 8:42 AM ET 
Turnpack, LLC
22425 S Scotland Ct
Ste 104
Queen Creek, AZ 85142
United States
14803311878
info@turnpack.comDetailsOrder Number: 4166D-15010
PO Number: PO26191738
Shipping Method: Unpaid Shipping
Tracking: 5598659931
Order DetailsOrder Number: 4166D-15010
PO Number: PO26191738Delivered (Displaying 2 of 2)Delivered 05/27/2026 Tracking 5598659931 Material Aluminum 6061-T6x (Best Available) Finish Standard Quantity 4/4 Delivered 05/27/2026 Tracking 5598659931 Material Aluminum 6061-T6x (Best Available) Finish Standard Quantity 2/2 Need help? Chat with our support team for instant assistance.Log into your dashboard to view all your orders and shipments.All orders are subject to the terms of Xometry's Customer Service Agreement. If you have any questions or concerns about your order, contact us.ISO 9001:2015, ISO 13485:2016, IATF 16949:2016, AS9100D, and CMMC Level 2 Certified | ITAR-registered
by "no-reply@xometry.com" <info@xometry.com> - 06:46 - 27 May 2026 -
Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs
Hi Garrett,Thanks for the update. You are correct that the set screws are adjustable to account for general tolerances of the toolbank assemblies within the machine. There are set screws for the left, right, and height adjustments. I'd suggest you dial in one and then match all the others; chances are they'll be very close. Let us know if you have any other questions.ChrisOn Wed, May 27, 2026 at 2:50 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:I looked at a few loading jigs, and testing them had some issues. I just found that the screws on either end was obstructing the loading, but I can just twist them more to fit. Each of the jigs have them twisted and sticking out at different lengths though. Is there a specific length they should be? Or should I just size them to slide easily in and out of the tool holders?
Just want to make sure these screws are for any other reason than easy loading/aligning to the tool holder itself 😊. I’ll go through the rest of them either today or tomorrow and let you know if I encounter any more issues.
Once I verify the other jigs are good to go, I’ll send the adapters back and shoot over the tracking number for you.Thanks!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 27, 2026 10:46 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
Sorry about that. We do check them for flatness and vacuum seal so it would be best if you can ship them back for RCA and we'll fix it. Hope this doesn't delay your project.
Any issues with the Loading Jigs?
Chris
On Wed, May 27, 2026 at 10:34 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Hi Chris,
I went through the rest of the delivery and found 3 more that do not slide all the way into the tool (for a total of 4x). Physically they look similar, but may have some slight warpage issues causing these issues. Any ideas on how to fix this? I’m afraid of trying to bend them to fix the warpage. Would you like me to ship them back for you to take a look?
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Garrett Davidson
Sent: Wednesday, May 27, 2026 8:04 AM
To: Christopher Berger <cberger@turnpack.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsSorry, these are two SEPARATE adapters. I’m going through the other adapters now, and will let you know if I see any more issues!
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 27, 2026 7:58 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
Thanks for the info. My fault on the partially engraved one, I was supposed to let you know but fell behind. We already have a replacement for that one in queue but I wanted to ship all 20 just in case you needed the full qty right away. Is this the same adapter you are having the issue with on the suction cup or is this a different one?
Chris
On Wed, May 27, 2026 at 7:50 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Unsure if this sent or if the full email did not send. I received a bunch of error messages.
Please find the video up in the fileXchange if you need!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Garrett Davidson
Sent: Tuesday, May 26, 2026 6:28 PM
To: 'Lorena Carrillo' <lcarrillo@turnpack.com>; 'Christopher Berger' <cberger@turnpack.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Chris/Turnpack,
I started opening up the box, and found an issue with one of the adapters:
As I slide the adapter into our tool, it stops here and does not allow us to slide it all the way to the vacuum port. The adapter itself seemed warped when placed on an optical table. I checked 5 more so far from the latest shipment and they all look good! Just this one is unable to slide in. I attached a video of myself trying to push it it and it not going all the way in without me having to physically lift the adapter into place and have a high risk of “confetti-ing” components in waffle packs. Let me know if it doesn’t come through. I also uploaded into our FileXchange system for you to review. Let me know if anyone needs access to this:
One of the 5 that I looked at after this one is missing most of the writing at the bottom of the adapter itself. Not a huge deal as it’s just cosmetic to us, but did want to let you know about it:
I will go through all the rest tomorrow morning and let you know if I encounter any more like this.
Can I send this one back to you to root cause or any ideas how to fix up? I could try to bend it but unsure how brittle the adapter itself is or if I’ll make it worse.
Thanks!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Garrett Davidson
Sent: Wednesday, May 20, 2026 4:23 PM
To: Lorena Carrillo <lcarrillo@turnpack.com>; 'Christopher Berger' <cberger@turnpack.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsThank you!!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Lorena Carrillo <lcarrillo@turnpack.com>
Sent: Wednesday, May 20, 2026 4:20 PM
To: 'Christopher Berger' <cberger@turnpack.com>; Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHello Team, the order has shipped complete today. Here is your tracking number for reference. 872056271057
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, May 19, 2026 11:18 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
We have the adapters back from anodizing but I slightly underestimated the assembly time. We are wrapping up the assembly today and tomorrow will be for engraving and testing and then we'll ship them out tomorrow.
The toolholder jigs are complete and ready to go.
Thanks
Chris
On Mon, May 18, 2026 at 4:29 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Hey Chris,
Were you able to ship out those parts? And have a tracking number if possible?
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 13, 2026 7:55 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsGarrett,
We experienced a slight delay because a machine was down, but parts are currently at anodizing. We are expediting that process, and then we anticipate two days for post-anodizing assembly & engraving. We might be able to ship it out Saturday, worst case it'll be Monday. I'll keep you posted when the parts come back from anodizing and then I should be able to confirm actual ship date.
Chris
On Wed, May 13, 2026 at 7:39 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Hey Chris,
Just checking if you think you’d be able to ship anything this week?
Thanks!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 4:54 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsPerfect. Thanks for confirming
On Tue, Apr 28, 2026 at 4:44 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Yeah that’s okay with me!
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 4:23 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsGarrett,
Yes. Example image below shows one side machined and the top not machined. If we machine all 4 sides they will all look like the side edge in the image below. Also, we did start with the adapters, once they are ready and in case the jigs are not I will let you know and we can do a partial shipment.
Thanks
Chris
On Tue, Apr 28, 2026 at 4:18 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Sorry, what do you mean by “Obscuring them”? would it “fog” the glass or make it not transparent?
The wafer pack adapters are a higher priority for us if possible! But no worries either way.
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 3:44 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
Making good progress. As of now it looks like we'll ship the order the week of 05/11. We had a question about the tool holder jigs. We would prefer to machine them on multiple sides but doing so would obscure them. Reason being is that the stock material has significant tolerancing, so facing all sides would ensure greater consistency. Any objections to that?
Chris
On Tue, Apr 28, 2026 at 2:54 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Hey Chris,
Hope you are doing well! Do you have an ETA for this order? (PO#3714362)
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Chris Berger <info@turnpack.com>
Sent: Tuesday, April 7, 2026 9:03 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Subject: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett, Attached is the quote for the adapters and loading jigs. Let me know if you need anything else. Chris Christopher Berger Phone: +1 [...] ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏
SO26141038
$ 69,200.00
Expires on 05/07/2026
Hi Garrett,
Attached is the quote for the adapters and loading jigs. Let me know if you need anything else.
Chris
Christopher BergerTurnpack — Efficiency Redefined Through Automation
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--Christopher Berger
by Chris Berger - 05:56 - 27 May 2026 -
RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs
I looked at a few loading jigs, and testing them had some issues. I just found that the screws on either end was obstructing the loading, but I can just twist them more to fit. Each of the jigs have them twisted and sticking out at different lengths though. Is there a specific length they should be? Or should I just size them to slide easily in and out of the tool holders?
Just want to make sure these screws are for any other reason than easy loading/aligning to the tool holder itself 😊. I’ll go through the rest of them either today or tomorrow and let you know if I encounter any more issues.
Once I verify the other jigs are good to go, I’ll send the adapters back and shoot over the tracking number for you.Thanks!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 27, 2026 10:46 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
Sorry about that. We do check them for flatness and vacuum seal so it would be best if you can ship them back for RCA and we'll fix it. Hope this doesn't delay your project.
Any issues with the Loading Jigs?
Chris
On Wed, May 27, 2026 at 10:34 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Hi Chris,
I went through the rest of the delivery and found 3 more that do not slide all the way into the tool (for a total of 4x). Physically they look similar, but may have some slight warpage issues causing these issues. Any ideas on how to fix this? I’m afraid of trying to bend them to fix the warpage. Would you like me to ship them back for you to take a look?
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Garrett Davidson
Sent: Wednesday, May 27, 2026 8:04 AM
To: Christopher Berger <cberger@turnpack.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsSorry, these are two SEPARATE adapters. I’m going through the other adapters now, and will let you know if I see any more issues!
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 27, 2026 7:58 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
Thanks for the info. My fault on the partially engraved one, I was supposed to let you know but fell behind. We already have a replacement for that one in queue but I wanted to ship all 20 just in case you needed the full qty right away. Is this the same adapter you are having the issue with on the suction cup or is this a different one?
Chris
On Wed, May 27, 2026 at 7:50 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Unsure if this sent or if the full email did not send. I received a bunch of error messages.
Please find the video up in the fileXchange if you need!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Garrett Davidson
Sent: Tuesday, May 26, 2026 6:28 PM
To: 'Lorena Carrillo' <lcarrillo@turnpack.com>; 'Christopher Berger' <cberger@turnpack.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Chris/Turnpack,
I started opening up the box, and found an issue with one of the adapters:
As I slide the adapter into our tool, it stops here and does not allow us to slide it all the way to the vacuum port. The adapter itself seemed warped when placed on an optical table. I checked 5 more so far from the latest shipment and they all look good! Just this one is unable to slide in. I attached a video of myself trying to push it it and it not going all the way in without me having to physically lift the adapter into place and have a high risk of “confetti-ing” components in waffle packs. Let me know if it doesn’t come through. I also uploaded into our FileXchange system for you to review. Let me know if anyone needs access to this:
One of the 5 that I looked at after this one is missing most of the writing at the bottom of the adapter itself. Not a huge deal as it’s just cosmetic to us, but did want to let you know about it:
I will go through all the rest tomorrow morning and let you know if I encounter any more like this.
Can I send this one back to you to root cause or any ideas how to fix up? I could try to bend it but unsure how brittle the adapter itself is or if I’ll make it worse.
Thanks!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Garrett Davidson
Sent: Wednesday, May 20, 2026 4:23 PM
To: Lorena Carrillo <lcarrillo@turnpack.com>; 'Christopher Berger' <cberger@turnpack.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsThank you!!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Lorena Carrillo <lcarrillo@turnpack.com>
Sent: Wednesday, May 20, 2026 4:20 PM
To: 'Christopher Berger' <cberger@turnpack.com>; Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHello Team, the order has shipped complete today. Here is your tracking number for reference. 872056271057
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, May 19, 2026 11:18 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
We have the adapters back from anodizing but I slightly underestimated the assembly time. We are wrapping up the assembly today and tomorrow will be for engraving and testing and then we'll ship them out tomorrow.
The toolholder jigs are complete and ready to go.
Thanks
Chris
On Mon, May 18, 2026 at 4:29 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Hey Chris,
Were you able to ship out those parts? And have a tracking number if possible?
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 13, 2026 7:55 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsGarrett,
We experienced a slight delay because a machine was down, but parts are currently at anodizing. We are expediting that process, and then we anticipate two days for post-anodizing assembly & engraving. We might be able to ship it out Saturday, worst case it'll be Monday. I'll keep you posted when the parts come back from anodizing and then I should be able to confirm actual ship date.
Chris
On Wed, May 13, 2026 at 7:39 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Hey Chris,
Just checking if you think you’d be able to ship anything this week?
Thanks!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 4:54 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsPerfect. Thanks for confirming
On Tue, Apr 28, 2026 at 4:44 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Yeah that’s okay with me!
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 4:23 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsGarrett,
Yes. Example image below shows one side machined and the top not machined. If we machine all 4 sides they will all look like the side edge in the image below. Also, we did start with the adapters, once they are ready and in case the jigs are not I will let you know and we can do a partial shipment.
Thanks
Chris
On Tue, Apr 28, 2026 at 4:18 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Sorry, what do you mean by “Obscuring them”? would it “fog” the glass or make it not transparent?
The wafer pack adapters are a higher priority for us if possible! But no worries either way.
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 3:44 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
Making good progress. As of now it looks like we'll ship the order the week of 05/11. We had a question about the tool holder jigs. We would prefer to machine them on multiple sides but doing so would obscure them. Reason being is that the stock material has significant tolerancing, so facing all sides would ensure greater consistency. Any objections to that?
Chris
On Tue, Apr 28, 2026 at 2:54 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Hey Chris,
Hope you are doing well! Do you have an ETA for this order? (PO#3714362)
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Chris Berger <info@turnpack.com>
Sent: Tuesday, April 7, 2026 9:03 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Subject: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett, Attached is the quote for the adapters and loading jigs. Let me know if you need anything else. Chris Christopher Berger Phone: +1 [...] ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏
SO26141038
$ 69,200.00
Expires on 05/07/2026
Hi Garrett,
Attached is the quote for the adapters and loading jigs. Let me know if you need anything else.
Chris
Christopher BergerTurnpack — Efficiency Redefined Through Automation
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
by Garrett Davidson - 05:51 - 27 May 2026 -
Re: RFQ
Hi Ivan,
We can square them; quote and lead time are the same. Let me know if that is satisfactory.
Best Regards,
Tony Haynes
Technical Sales Representative
FLODRAULIC
Cell 480.997.2852
Fax 480.921.3272
1150 N. FIESTA BLVD. GILBERT, AZ 85233
ISO 9001:2015 Registered
*** Important Notice: Send all Inquiries/Orders to our new Customer Service email address SWSales@flodraulicgroup.com***
From: Ivan Arevalo <iarevalo@turnpack.com>
Sent: Wednesday, May 27, 2026 9:49 AM
To: Tony Haynes <thaynes@flodraulicgroup.com>
Cc: Brandon Benavidez <bbenavidez@turnpack.com>; Christopher Berger <cberger@turnpack.com>; Info at Turnpack <info@turnpack.com>
Subject: Re: RFQ
Hi Tony,
Yes, please square those up so we can get the caps on.
I'll get with Chris and Brandon to determine how we want to move forward.
Thanks,
Ivan
On Tue, May 26, 2026 at 10:57 AM Tony Haynes <thaynes@flodraulicgroup.com> wrote:Hi Ivan,
Here is the Simple Side Module Enclosure quote project number 26359M1 for Turnpack.We aligned the frames and connectors for the simple side module. Please review
Cost for Kit: $2,243.90 each
Cost for Assembled: $2,809.61 each
5-7 Days
Here is the base module top enclosure quote project number 26358M1 for Turnpack.*****The bars you want cover caps on are not square on the end so will not go on.
*****If you want them squared, we can square them up and then add the end caps.
Cost for Kit: $1,012.17 each
Cost for Assembled: $1,272.10 each
5-7 Days
Best Regards,Tony Haynes
Technical Sales Representative
FLODRAULIC
Cell 480.997.2852
Fax 480.921.3272
1150 N. FIESTA BLVD. GILBERT, AZ 85233
ISO 9001:2015 Registered
*** Important Notice: Send all Inquiries/Orders to our new Customer Service email address SWSales@flodraulicgroup.com***
From: Ivan Arevalo <iarevalo@turnpack.com>
Sent: Thursday, May 21, 2026 5:41 PM
To: Tony Haynes <thaynes@flodraulicgroup.com>
Cc: Brandon Benavidez <bbenavidez@turnpack.com>; Christopher Berger <cberger@turnpack.com>; Info at Turnpack <info@turnpack.com>
Subject: RFQ
Hi Tony,
I've attached two .scene files for some extrusions that we would like pricing on below.
The Base Module Top Enclosure should have the flat edge of the 40x80 3E facing outward. In MAYCAD, it shows up red as an error but we just want the slotted sides to be facing inward toward the enclosure. Additionally, I couldn't get the rubber caps onto the ends of the angled top extrusions in MAYCAD, but we want rubber caps on those.
For the Simple Side Module Enclosure, do not quote the two "hurdles" that connect the back of the enclosure and the front 120x40 extrusion. Those are just placeholders to properly render the mating connection points. We also need additional mounting locations along the front extrusion for better support due to the extended length.
Please reach out with any questions or concerns.
Thank you for your assistance.
Best,Ivan
by Tony Haynes - 05:21 - 27 May 2026 -
Re: Jabil 2200Evo
Hi Chris,
Any update on sourcing the spare bond head?
Thanks,Rod
From: Christopher Berger <cberger@turnpack.com>
Sent: Friday, May 15, 2026 8:01 AM
To: Rod Mapanao <Rod_Mapanao@jabil.com>
Cc: notifications@turnpack.com <notifications@turnpack.com>; Hung Lam <Hung_Lam@jabil.com>; Quyen Chu <Quyen_Chu@jabil.com>; Resty Fonte Familara <RestyFonte_Familara@jabil.com>; lcarrillo@turnpack.com <lcarrillo@turnpack.com>; info@turnpack.com <info@turnpack.com>
Subject: Re: Jabil 2200EvoEXTERNAL EMAIL: Exercise caution when handling links and attachments.
Hi Rod,
Yes I did miss this. Sorry about that. Let me see if I can get a heated bondhead for you. I will touch base with you later today.
Chris
On Thu, May 14, 2026 at 12:13 PM Rod Mapanao <Rod_Mapanao@jabil.com> wrote:
Hi Chris,
I am following this up, in case you missed this email.I also added email addresses from our records.
Please send us a quote for Evo+ heated bond head replacement - parts and labor.
Thanks,ROD MAPANAO
Process DevelopmentMTI
Jabil MTI
30 Great Oaks Blvd.,
San Jose, CA 95119
From: Rod Mapanao <Rod_Mapanao@Jabil.com>
Sent: Friday, May 8, 2026 5:07 PM
To: Christopher Berger <cberger@turnpack.com>
Cc: Hung Lam <Hung_Lam@jabil.com>; Quyen Chu <Quyen_Chu@jabil.com>; Resty Fonte Familara <RestyFonte_Familara@jabil.com>
Subject: Re: Jabil 2200EvoHi Chris,
How are you? It's been a year since the service.Following up on the spares especially for the heated bond head on Machine#1 SN 950 2219 3998Ours finally gave up. Do you have a spare and can you replace ours?Please send us a quote for the spare and installation.
Thanks,Rod
From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, April 16, 2025 8:12 AM
To: Rod Mapanao <Rod_Mapanao@jabil.com>
Cc: Hung Lam <Hung_Lam@jabil.com>; Quyen Chu <Quyen_Chu@jabil.com>; Resty Fonte Familara <RestyFonte_Familara@jabil.com>
Subject: Re: Jabil 2200EvoEXTERNAL EMAIL: Exercise caution when handling links and attachments.
Hi Rod,
Attached are the two service reports for last weeks visit. I'll be sending you a quote for the recommended parts later today.
Chris
On Thu, Feb 27, 2025 at 1:02 PM Rod Mapanao <Rod_Mapanao@jabil.com> wrote:
Hi Chris,We've the machines to another building but the cleanroom is yet to be certified.While waiting, we could have the machines serviced before moving them again.Could you please send us a new quotation to diagnose our two 2200Evo.
Thanks and best regards,Rod
From: Chris Berger <notifications@turnpack.com>
Sent: Thursday, October 10, 2024 3:45 PM
To: Rod Mapanao <rod_mapanao@jabil.com>
Subject: Turnpack, LLC Quotation (Ref SO2441764)You don't often get email from notifications@turnpack.com. Learn why this is importantEXTERNAL EMAIL: Exercise caution when handling links and attachments.
Hi Rod,
Attached is the quote for 1-day service. Let us know if you need anything else?
Chris
Powered by Odoo
--
Christopher Berger
--
Christopher Berger
by Rod Mapanao - 03:31 - 27 May 2026 -
Re: 7D PO 260069 status?
Hi Greg,Yes we got both orders in production. I will confirm a ship date with you Friday. We are currently battling some technical difficulties with the lathe and are in communication with the Service Engineer. I will keep you posted.And yes we will replace the bushing, no problem.ChrisOn Wed, May 27, 2026 at 6:02 AM Greg Fraser <greg.fraser@7dkmetrology.com> wrote:Hi Chris,
Can you please update us on status of PO 260069?
Also, did I mention we have Qty 1 of the 0160216-A Brass bushing with a bad thread. Are you able to add Qty 1 to this PO or next open PO 260099 to replace this bad unit?
Thanks very much,
Greg
GREG FRASER 55 Fleming Drive
Lead Hardware Engineer Units 13-17, Cambridge, ON
(226) 606-3126 Canada N1T 2A9
--Christopher Berger
by Chris Berger - 02:46 - 27 May 2026 -
RE: Company Merger
Dear Lorena and Christopher,
Could you inform us please if those PO’s are in production and you can meet the requested delivery date for both PO’s?
Thank you in advance!
Best regards,
Kate
From: Kate Khomenko
Sent: May 20, 2026 9:44 AM
To: 'info@turnpack.com' <info@turnpack.com>
Cc: Accounting 7D Kinematic Metrology Inc <accounting@7dkmetrology.com>; Greg Fraser <greg.fraser@7dkmetrology.com>; Caroline Tremblay <caroline.tremblay@7dkmetrology.com>; Finances 7D Kinematic Metrology Inc <finances@7dkmetrology.com>
Subject: RE: Company MergerHello Lorena,
Currently we have 2 open PO’s, please find attached.
Best regards,
Kate
From: info@turnpack.com <info@turnpack.com>
Sent: May 19, 2026 3:47 PM
To: Kate Khomenko <Kate.Khomenko@7dkmetrology.com>; Accounting 7D Kinematic Metrology Inc <accounting@7dkmetrology.com>; Greg Fraser <greg.fraser@7dkmetrology.com>; Caroline Tremblay <caroline.tremblay@7dkmetrology.com>; Finances 7D Kinematic Metrology Inc <finances@7dkmetrology.com>
Subject: RE: Company MergerHello Team, I wanted to follow and confirm POs are being sent to the info@turnpack.com email for processing. Chris said there was an order placed but I am not seeing the PO come through. If so are you able to resend?
From: Kate Khomenko <Kate.Khomenko@7dkmetrology.com>
Sent: Thursday, January 22, 2026 12:06 PM
To: Lorena <info@turnpack.com>; Accounting 7D Kinematic Metrology Inc <accounting@7dkmetrology.com>; Greg Fraser <greg.fraser@7dkmetrology.com>; Caroline Tremblay <caroline.tremblay@7dkmetrology.com>; Finances 7D Kinematic Metrology Inc <finances@7dkmetrology.com>
Subject: RE: Company MergerThank you Lorena,
I’ve created a new supplier card in our system based on provided info. I think it is enough for now.
Best regards,
Kate
From: Lorena <info@turnpack.com>
Sent: January 22, 2026 12:29 PM
To: Kate Khomenko <Kate.Khomenko@7dkmetrology.com>; Accounting 7D Kinematic Metrology Inc <accounting@7dkmetrology.com>; Greg Fraser <greg.fraser@7dkmetrology.com>; Caroline Tremblay <caroline.tremblay@7dkmetrology.com>; Finances 7D Kinematic Metrology Inc <finances@7dkmetrology.com>
Subject: RE: Company MergerAttached is our ACH information.
Phone and address below.
All paperwork goes to info@turnpack.com (purchase orders, shipping requests, account inquiries) this is a team email for faster responses.
Quote/sales requests go to cberger@turnpack.com and preferably CC info@turnpack.com
Let me know if you have any questions.
Lorena Carrillo
Office Manager
Office: 480-331-1878
Line: 781-938-006922425 S Scotland Ct, Suite104, Queen Creek, AZ 85142
lcarrillo@turnpack.com | www.turnpack.com
https://www.turnpack.com/midas-rework/delidderFrom: Kate Khomenko <Kate.Khomenko@7dkmetrology.com>
Sent: Thursday, January 22, 2026 10:06 AM
To: Lorena <info@turnpack.com>; Accounting 7D Kinematic Metrology Inc <accounting@7dkmetrology.com>; Greg Fraser <greg.fraser@7dkmetrology.com>; Caroline Tremblay <caroline.tremblay@7dkmetrology.com>; Finances 7D Kinematic Metrology Inc <finances@7dkmetrology.com>
Subject: RE: Company MergerHello Lorena,
Please find below our company data to be entered to your database. We would kindly appreciate if you could inform us your new data in the same format as well, since I don’t have full data in my system for Birch Mnf.
General:
- Company name: 7D KINEMATIC METROLOGY INC.
- Company website: https://7dkmetrology.com/
- Tax ID number: 72624 5913 RC0001
- Company phone number: 1-519-498-0548 (as our website)
Contacts:
- Kate Khomenko, Supply Chain Specialist / 226-929-1392 / kate.khomenko@7dkmetrology.com
- Greg Fraser, Production Manager / 226-606-31-26 / greg.fraser@7dkmetrology.com
- Jeff Bueckert, Director of Engineering & Operations / jeff.bueckert@7dkmetrology.com
- Finance department / Email finances@7dkmetrology.com
Purchasing/Sales terms:
- Shipping/Receiving address: 55 Fleming Drive, units 13-17, Cambridge, ON, N1T 2A9
- Purchasing/Sales address: (same as shipping/receiving address)
- Shipment terms (INCOTERMS): EXW, please use our UPS account 88WE37.
- Payment terms: Net 30 day
Best regards,
KATE KHOMENKO 55 Fleming Drive
Supply Chain Specialist Units 13-17, Cambridge, ON
(226) 929-1392 Canada N1T 2A9
From: Lorena <info@turnpack.com>
Sent: December 17, 2025 11:02 AM
To: Accounting 7D Kinematic Metrology Inc <accounting@7dkmetrology.com>; Greg Fraser <greg.fraser@7dkmetrology.com>; Caroline Tremblay <caroline.tremblay@7dkmetrology.com>; Finances 7D Kinematic Metrology Inc <finances@7dkmetrology.com>
Cc: Kate Khomenko <Kate.Khomenko@7dkmetrology.com>
Subject: Company MergerHello 7D Team.
I hope this message finds you well.
I am writing to inform you that Birch Manufacturing AZ has been acquired by Turnpack LLC as of December 31, 2025.
Please send any necessary paperwork to establish Turnpack LLC in your database. Kindly note that aside from the company name change, no other modifications are being made.
Additionally, please be aware that Turnpack LLC also acquired Midas Technology as of June 2025.
Please let me know if you need any further information or documentation from our side.
Thank you for your attention to this matter.
Lorena Carrillo
Office Manager
Office: 480-331-1878
Line: 781-938-006922425 S Scotland Ct, Suite104, Queen Creek, AZ 85142
lcarrillo@turnpack.com | www.turnpack.com
https://www.turnpack.com/midas-rework/delidder
by "Kate Khomenko" <Kate.Khomenko@7dkmetrology.com> - 02:42 - 27 May 2026 -
Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs
Hi Garrett,Sorry about that. We do check them for flatness and vacuum seal so it would be best if you can ship them back for RCA and we'll fix it. Hope this doesn't delay your project.Any issues with the Loading Jigs?ChrisOn Wed, May 27, 2026 at 10:34 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:Hi Chris,
I went through the rest of the delivery and found 3 more that do not slide all the way into the tool (for a total of 4x). Physically they look similar, but may have some slight warpage issues causing these issues. Any ideas on how to fix this? I’m afraid of trying to bend them to fix the warpage. Would you like me to ship them back for you to take a look?
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Garrett Davidson
Sent: Wednesday, May 27, 2026 8:04 AM
To: Christopher Berger <cberger@turnpack.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsSorry, these are two SEPARATE adapters. I’m going through the other adapters now, and will let you know if I see any more issues!
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 27, 2026 7:58 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
Thanks for the info. My fault on the partially engraved one, I was supposed to let you know but fell behind. We already have a replacement for that one in queue but I wanted to ship all 20 just in case you needed the full qty right away. Is this the same adapter you are having the issue with on the suction cup or is this a different one?
Chris
On Wed, May 27, 2026 at 7:50 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Unsure if this sent or if the full email did not send. I received a bunch of error messages.
Please find the video up in the fileXchange if you need!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Garrett Davidson
Sent: Tuesday, May 26, 2026 6:28 PM
To: 'Lorena Carrillo' <lcarrillo@turnpack.com>; 'Christopher Berger' <cberger@turnpack.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Chris/Turnpack,
I started opening up the box, and found an issue with one of the adapters:
As I slide the adapter into our tool, it stops here and does not allow us to slide it all the way to the vacuum port. The adapter itself seemed warped when placed on an optical table. I checked 5 more so far from the latest shipment and they all look good! Just this one is unable to slide in. I attached a video of myself trying to push it it and it not going all the way in without me having to physically lift the adapter into place and have a high risk of “confetti-ing” components in waffle packs. Let me know if it doesn’t come through. I also uploaded into our FileXchange system for you to review. Let me know if anyone needs access to this:
One of the 5 that I looked at after this one is missing most of the writing at the bottom of the adapter itself. Not a huge deal as it’s just cosmetic to us, but did want to let you know about it:
I will go through all the rest tomorrow morning and let you know if I encounter any more like this.
Can I send this one back to you to root cause or any ideas how to fix up? I could try to bend it but unsure how brittle the adapter itself is or if I’ll make it worse.
Thanks!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Garrett Davidson
Sent: Wednesday, May 20, 2026 4:23 PM
To: Lorena Carrillo <lcarrillo@turnpack.com>; 'Christopher Berger' <cberger@turnpack.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsThank you!!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Lorena Carrillo <lcarrillo@turnpack.com>
Sent: Wednesday, May 20, 2026 4:20 PM
To: 'Christopher Berger' <cberger@turnpack.com>; Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHello Team, the order has shipped complete today. Here is your tracking number for reference. 872056271057
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, May 19, 2026 11:18 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
We have the adapters back from anodizing but I slightly underestimated the assembly time. We are wrapping up the assembly today and tomorrow will be for engraving and testing and then we'll ship them out tomorrow.
The toolholder jigs are complete and ready to go.
Thanks
Chris
On Mon, May 18, 2026 at 4:29 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Hey Chris,
Were you able to ship out those parts? And have a tracking number if possible?
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 13, 2026 7:55 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsGarrett,
We experienced a slight delay because a machine was down, but parts are currently at anodizing. We are expediting that process, and then we anticipate two days for post-anodizing assembly & engraving. We might be able to ship it out Saturday, worst case it'll be Monday. I'll keep you posted when the parts come back from anodizing and then I should be able to confirm actual ship date.
Chris
On Wed, May 13, 2026 at 7:39 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Hey Chris,
Just checking if you think you’d be able to ship anything this week?
Thanks!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 4:54 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsPerfect. Thanks for confirming
On Tue, Apr 28, 2026 at 4:44 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Yeah that’s okay with me!
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 4:23 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsGarrett,
Yes. Example image below shows one side machined and the top not machined. If we machine all 4 sides they will all look like the side edge in the image below. Also, we did start with the adapters, once they are ready and in case the jigs are not I will let you know and we can do a partial shipment.
Thanks
Chris
On Tue, Apr 28, 2026 at 4:18 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Sorry, what do you mean by “Obscuring them”? would it “fog” the glass or make it not transparent?
The wafer pack adapters are a higher priority for us if possible! But no worries either way.
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 3:44 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
Making good progress. As of now it looks like we'll ship the order the week of 05/11. We had a question about the tool holder jigs. We would prefer to machine them on multiple sides but doing so would obscure them. Reason being is that the stock material has significant tolerancing, so facing all sides would ensure greater consistency. Any objections to that?
Chris
On Tue, Apr 28, 2026 at 2:54 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Hey Chris,
Hope you are doing well! Do you have an ETA for this order? (PO#3714362)
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Chris Berger <info@turnpack.com>
Sent: Tuesday, April 7, 2026 9:03 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Subject: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett, Attached is the quote for the adapters and loading jigs. Let me know if you need anything else. Chris Christopher Berger Phone: +1 [...] ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏
SO26141038
$ 69,200.00
Expires on 05/07/2026
Hi Garrett,
Attached is the quote for the adapters and loading jigs. Let me know if you need anything else.
Chris
Christopher BergerTurnpack — Efficiency Redefined Through Automation
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--Christopher Berger
by Chris Berger - 01:47 - 27 May 2026 -
Delivered: "wowstick Mini Electric..."
Your package was delivered!Delivered todayIt was handed directly to a receptionist or someone at a front desk.Turnpack - QUEEN CREEK, AZOrder # 113-5765356-0253853
Return or replace items in Your Orders. How was your delivery?©2026 Amazon.com, Inc. or its affiliates. Amazon and all related marks are trademarks of Amazon.com, Inc. or its affiliates, Amazon.com, Inc. 410 Terry Avenue N., Seattle, WA 98109.
by "Amazon.com" <order-update@amazon.com> - 01:47 - 27 May 2026 -
Get free 6-month trial of Xero when you join now
Email Template
Members can try Xero free1 for 6 months
Join Walmart Business+ for this special online bookkeeping offer.
Xero helps you control your cash flowWith automated invoicing & online payments, Xero makes it easier to track your budget.
Online convenience & features that save timeWith easy access & real-time reporting, Xero keeps your books while you focus on business.1Offer available to new Xero Customers only. Eligibility & terms apply.
Questions? Visit our Help CenterPlease note that product availability is limited and prices are subject to change. Do not reply to this email. The inbox is not monitored. If you require assistance, please click here for help. Walmart Business protects your security and privacy. We will never ask for personal information (such as passwords or credit card numbers) in an email newsletter. If you receive such a request, please do not respond to the email. Learn more. See our Privacy Policy. This email is a Walmart Business advertisement. If you do not want to receive these email updates, click here to unsubscribe. Walmart Business, 702 SW 8th St, Bentonville, AR 72712 © 2026 Walmart.
by "Walmart Business" <newsletter@em.business.walmart.com> - 01:46 - 27 May 2026 -
RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs
Hi Chris,
I went through the rest of the delivery and found 3 more that do not slide all the way into the tool (for a total of 4x). Physically they look similar, but may have some slight warpage issues causing these issues. Any ideas on how to fix this? I’m afraid of trying to bend them to fix the warpage. Would you like me to ship them back for you to take a look?
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Garrett Davidson
Sent: Wednesday, May 27, 2026 8:04 AM
To: Christopher Berger <cberger@turnpack.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsSorry, these are two SEPARATE adapters. I’m going through the other adapters now, and will let you know if I see any more issues!
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 27, 2026 7:58 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
Thanks for the info. My fault on the partially engraved one, I was supposed to let you know but fell behind. We already have a replacement for that one in queue but I wanted to ship all 20 just in case you needed the full qty right away. Is this the same adapter you are having the issue with on the suction cup or is this a different one?
Chris
On Wed, May 27, 2026 at 7:50 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Unsure if this sent or if the full email did not send. I received a bunch of error messages.
Please find the video up in the fileXchange if you need!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Garrett Davidson
Sent: Tuesday, May 26, 2026 6:28 PM
To: 'Lorena Carrillo' <lcarrillo@turnpack.com>; 'Christopher Berger' <cberger@turnpack.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Chris/Turnpack,
I started opening up the box, and found an issue with one of the adapters:
As I slide the adapter into our tool, it stops here and does not allow us to slide it all the way to the vacuum port. The adapter itself seemed warped when placed on an optical table. I checked 5 more so far from the latest shipment and they all look good! Just this one is unable to slide in. I attached a video of myself trying to push it it and it not going all the way in without me having to physically lift the adapter into place and have a high risk of “confetti-ing” components in waffle packs. Let me know if it doesn’t come through. I also uploaded into our FileXchange system for you to review. Let me know if anyone needs access to this:
One of the 5 that I looked at after this one is missing most of the writing at the bottom of the adapter itself. Not a huge deal as it’s just cosmetic to us, but did want to let you know about it:
I will go through all the rest tomorrow morning and let you know if I encounter any more like this.
Can I send this one back to you to root cause or any ideas how to fix up? I could try to bend it but unsure how brittle the adapter itself is or if I’ll make it worse.
Thanks!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Garrett Davidson
Sent: Wednesday, May 20, 2026 4:23 PM
To: Lorena Carrillo <lcarrillo@turnpack.com>; 'Christopher Berger' <cberger@turnpack.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsThank you!!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Lorena Carrillo <lcarrillo@turnpack.com>
Sent: Wednesday, May 20, 2026 4:20 PM
To: 'Christopher Berger' <cberger@turnpack.com>; Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHello Team, the order has shipped complete today. Here is your tracking number for reference. 872056271057
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, May 19, 2026 11:18 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
We have the adapters back from anodizing but I slightly underestimated the assembly time. We are wrapping up the assembly today and tomorrow will be for engraving and testing and then we'll ship them out tomorrow.
The toolholder jigs are complete and ready to go.
Thanks
Chris
On Mon, May 18, 2026 at 4:29 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Hey Chris,
Were you able to ship out those parts? And have a tracking number if possible?
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 13, 2026 7:55 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsGarrett,
We experienced a slight delay because a machine was down, but parts are currently at anodizing. We are expediting that process, and then we anticipate two days for post-anodizing assembly & engraving. We might be able to ship it out Saturday, worst case it'll be Monday. I'll keep you posted when the parts come back from anodizing and then I should be able to confirm actual ship date.
Chris
On Wed, May 13, 2026 at 7:39 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Hey Chris,
Just checking if you think you’d be able to ship anything this week?
Thanks!
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 4:54 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsPerfect. Thanks for confirming
On Tue, Apr 28, 2026 at 4:44 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Yeah that’s okay with me!
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 4:23 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsGarrett,
Yes. Example image below shows one side machined and the top not machined. If we machine all 4 sides they will all look like the side edge in the image below. Also, we did start with the adapters, once they are ready and in case the jigs are not I will let you know and we can do a partial shipment.
Thanks
Chris
On Tue, Apr 28, 2026 at 4:18 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Sorry, what do you mean by “Obscuring them”? would it “fog” the glass or make it not transparent?
The wafer pack adapters are a higher priority for us if possible! But no worries either way.
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 3:44 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett,
Making good progress. As of now it looks like we'll ship the order the week of 05/11. We had a question about the tool holder jigs. We would prefer to machine them on multiple sides but doing so would obscure them. Reason being is that the stock material has significant tolerancing, so facing all sides would ensure greater consistency. Any objections to that?
Chris
On Tue, Apr 28, 2026 at 2:54 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:
Hey Chris,
Hope you are doing well! Do you have an ETA for this order? (PO#3714362)
Thanks,
Garrett Davidson
MicroElectronics Hardware Development Engineer
+1 (425) 539 - 1448
From: Chris Berger <info@turnpack.com>
Sent: Tuesday, April 7, 2026 9:03 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Subject: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading JigsHi Garrett, Attached is the quote for the adapters and loading jigs. Let me know if you need anything else. Chris Christopher Berger Phone: +1 [...] ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏
SO26141038
$ 69,200.00
Expires on 05/07/2026
Hi Garrett,
Attached is the quote for the adapters and loading jigs. Let me know if you need anything else.
Chris
Christopher BergerTurnpack — Efficiency Redefined Through Automation
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
--
Christopher Berger
by Garrett Davidson - 01:37 - 27 May 2026
