Archivados
Info Inbox
info@turnpack.com
Re: RFQ
Hi Ivan,
Thanks for sending this over, we are reviewing the file and will follow up with a quote!
Best Regards,
|
|
|
Tony Haynes Technical Sales Representative FLODRAULIC
|
*** Important Notice: Send all
Inquiries/Orders to our new Customer Service email address SWSales@flodraulicgroup.com***
From: Ivan Arevalo <iarevalo@turnpack.com>
Sent: Thursday, May 21, 2026 5:41 PM
To: Tony Haynes <thaynes@flodraulicgroup.com>
Cc: Brandon Benavidez <bbenavidez@turnpack.com>; Christopher Berger <cberger@turnpack.com>; Info at Turnpack <info@turnpack.com>
Subject: RFQ
Sent: Thursday, May 21, 2026 5:41 PM
To: Tony Haynes <thaynes@flodraulicgroup.com>
Cc: Brandon Benavidez <bbenavidez@turnpack.com>; Christopher Berger <cberger@turnpack.com>; Info at Turnpack <info@turnpack.com>
Subject: RFQ
Hi Tony,
I've attached two .scene files for some extrusions that we would like pricing on below.
The Base Module Top Enclosure should have the flat edge of the 40x80 3E facing outward. In MAYCAD, it shows up red as an error but we just want the slotted sides to be facing inward toward the enclosure. Additionally, I couldn't get the rubber caps onto
the ends of the angled top extrusions in MAYCAD, but we want rubber caps on those.
For the Simple Side Module Enclosure, do not quote the two "hurdles" that connect the back of the enclosure and the front 120x40 extrusion. Those are just placeholders to properly render the mating connection points. We also need additional mounting locations
along the front extrusion for better support due to the extended length.
Please reach out with any questions or concerns.
Please reach out with any questions or concerns.
Thank you for your assistance.
Best,
Ivan
por Tony Haynes - 11:31 - 22 may. 2026
Referencia
-
RFQ
Hi Tony,I've attached two .scene files for some extrusions that we would like pricing on below.The Base Module Top Enclosure should have the flat edge of the 40x80 3E facing outward. In MAYCAD, it shows up red as an error but we just want the slotted sides to be facing inward toward the enclosure. Additionally, I couldn't get the rubber caps onto the ends of the angled top extrusions in MAYCAD, but we want rubber caps on those.For the Simple Side Module Enclosure, do not quote the two "hurdles" that connect the back of the enclosure and the front 120x40 extrusion. Those are just placeholders to properly render the mating connection points. We also need additional mounting locations along the front extrusion for better support due to the extended length.
Please reach out with any questions or concerns.Thank you for your assistance.Best,Ivan
por Ivan Arevalo - 08:41 - 21 may. 2026-
Re: RFQ
Hi Ivan,
Thanks for sending this over, we are reviewing the file and will follow up with a quote!
Best Regards,
Tony Haynes
Technical Sales Representative
FLODRAULIC
Cell 480.997.2852
Fax 480.921.3272
1150 N. FIESTA BLVD. GILBERT, AZ 85233
ISO 9001:2015 Registered
*** Important Notice: Send all Inquiries/Orders to our new Customer Service email address SWSales@flodraulicgroup.com***
From: Ivan Arevalo <iarevalo@turnpack.com>
Sent: Thursday, May 21, 2026 5:41 PM
To: Tony Haynes <thaynes@flodraulicgroup.com>
Cc: Brandon Benavidez <bbenavidez@turnpack.com>; Christopher Berger <cberger@turnpack.com>; Info at Turnpack <info@turnpack.com>
Subject: RFQHi Tony,
I've attached two .scene files for some extrusions that we would like pricing on below.
The Base Module Top Enclosure should have the flat edge of the 40x80 3E facing outward. In MAYCAD, it shows up red as an error but we just want the slotted sides to be facing inward toward the enclosure. Additionally, I couldn't get the rubber caps onto the ends of the angled top extrusions in MAYCAD, but we want rubber caps on those.
For the Simple Side Module Enclosure, do not quote the two "hurdles" that connect the back of the enclosure and the front 120x40 extrusion. Those are just placeholders to properly render the mating connection points. We also need additional mounting locations along the front extrusion for better support due to the extended length.
Please reach out with any questions or concerns.
Thank you for your assistance.
Best,Ivan
por Tony Haynes - 11:31 - 22 may. 2026
-