Info Inbox

RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

I looked at a few loading jigs, and testing them had some issues. I just found that the screws on either end was obstructing the loading, but I can just twist them more to fit. Each of the jigs have them twisted and sticking out at different lengths though. Is there a specific length they should be? Or should I just size them to slide easily in and out of the tool holders?

Just want to make sure these screws are for any other reason than easy loading/aligning to the tool holder itself 😊. I’ll go through the rest of them either today or tomorrow and let you know if I encounter any more issues.

Once I verify the other jigs are good to go, I’ll send the adapters back and shoot over the tracking number for you.

Thanks!

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 27, 2026 10:46 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Hi Garrett,

Sorry about that. We do check them for flatness and vacuum seal so it would be best if you can ship them back for RCA and we'll fix it. Hope this doesn't delay your project.

Any issues with the Loading Jigs?

Chris

On Wed, May 27, 2026 at 10:34 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:

Hi Chris,

I went through the rest of the delivery and found 3 more that do not slide all the way into the tool (for a total of 4x). Physically they look similar, but may have some slight warpage issues causing these issues. Any ideas on how to fix this? I’m afraid of trying to bend them to fix the warpage. Would you like me to ship them back for you to take a look?

Thanks,

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Garrett Davidson
Sent: Wednesday, May 27, 2026 8:04 AM
To: Christopher Berger <cberger@turnpack.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Sorry, these are two SEPARATE adapters. I’m going through the other adapters now, and will let you know if I see any more issues!

Thanks,

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 27, 2026 7:58 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Hi Garrett,

Thanks for the info. My fault on the partially engraved one, I was supposed to let you know but fell behind. We already have a replacement for that one in queue but I wanted to ship all 20 just in case you needed the full qty right away. Is this the same adapter you are having the issue with on the suction cup or is this a different one?

Chris

On Wed, May 27, 2026 at 7:50 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:

Unsure if this sent or if the full email did not send. I received a bunch of error messages.

Please find the video up in the fileXchange if you need!

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Garrett Davidson
Sent: Tuesday, May 26, 2026 6:28 PM
To: 'Lorena Carrillo' <lcarrillo@turnpack.com>; 'Christopher Berger' <cberger@turnpack.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Hi Chris/Turnpack,

I started opening up the box, and found an issue with one of the adapters:

As I slide the adapter into our tool, it stops here and does not allow us to slide it all the way to the vacuum port. The adapter itself seemed warped when placed on an optical table. I checked 5 more so far from the latest shipment and they all look good! Just this one is unable to slide in. I attached a video of myself trying to push it it and it not going all the way in without me having to physically lift the adapter into place and have a high risk of “confetti-ing” components in waffle packs. Let me know if it doesn’t come through. I also uploaded into our FileXchange system for you to review. Let me know if anyone needs access to this:

One of the 5 that I looked at after this one is missing most of the writing at the bottom of the adapter itself. Not a huge deal as it’s just cosmetic to us, but did want to let you know about it:

I will go through all the rest tomorrow morning and let you know if I encounter any more like this.

Can I send this one back to you to root cause or any ideas how to fix up? I could try to bend it but unsure how brittle the adapter itself is or if I’ll make it worse.

Thanks!

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Garrett Davidson
Sent: Wednesday, May 20, 2026 4:23 PM
To: Lorena Carrillo <lcarrillo@turnpack.com>; 'Christopher Berger' <cberger@turnpack.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Thank you!!

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Lorena Carrillo <lcarrillo@turnpack.com>
Sent: Wednesday, May 20, 2026 4:20 PM
To: 'Christopher Berger' <cberger@turnpack.com>; Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Hello Team, the order has shipped complete today. Here is your tracking number for reference. 872056271057

From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, May 19, 2026 11:18 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Hi Garrett,

We have the adapters back from anodizing but I slightly underestimated the assembly time. We are wrapping up the assembly today and tomorrow will be for engraving and testing and then we'll ship them out tomorrow.

The toolholder jigs are complete and ready to go.

Thanks

Chris

On Mon, May 18, 2026 at 4:29 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:

Hey Chris,

Were you able to ship out those parts? And have a tracking number if possible?

Thanks,

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 13, 2026 7:55 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Garrett,

We experienced a slight delay because a machine was down, but parts are currently at anodizing. We are expediting that process, and then we anticipate two days for post-anodizing assembly & engraving. We might be able to ship it out Saturday, worst case it'll be Monday. I'll keep you posted when the parts come back from anodizing and then I should be able to confirm actual ship date.

Chris

On Wed, May 13, 2026 at 7:39 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:

Hey Chris,

Just checking if you think you’d be able to ship anything this week?

Thanks!

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 4:54 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Perfect. Thanks for confirming

On Tue, Apr 28, 2026 at 4:44 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:

Yeah that’s okay with me!

Thanks,

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 4:23 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Garrett,

Yes. Example image below shows one side machined and the top not machined. If we machine all 4 sides they will all look like the side edge in the image below. Also, we did start with the adapters, once they are ready and in case the jigs are not I will let you know and we can do a partial shipment.

Thanks

Chris

On Tue, Apr 28, 2026 at 4:18 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:

Sorry, what do you mean by “Obscuring them”? would it “fog” the glass or make it not transparent?

The wafer pack adapters are a higher priority for us if possible! But no worries either way.

Thanks,

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 3:44 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Hi Garrett,

Making good progress. As of now it looks like we'll ship the order the week of 05/11. We had a question about the tool holder jigs. We would prefer to machine them on multiple sides but doing so would obscure them. Reason being is that the stock material has significant tolerancing, so facing all sides would ensure greater consistency. Any objections to that?

Chris

On Tue, Apr 28, 2026 at 2:54 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:

Hey Chris,

Hope you are doing well! Do you have an ETA for this order? (PO#3714362)

Thanks,

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Chris Berger <info@turnpack.com>
Sent: Tuesday, April 7, 2026 9:03 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Subject: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Hi Garrett, Attached is the quote for the adapters and loading jigs. Let me know if you need anything else. Chris Christopher Berger Phone: +1 [...] ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏

Sign & Pay Quotation

SO26141038
$ 69,200.00
Expires on 05/07/2026

Hi Garrett,

Attached is the quote for the adapters and loading jigs. Let me know if you need anything else.

Chris

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

Turnpack, LLC

+1 480-331-1878 | info@turnpack.com | https://www.turnpack.com

Turnpack — Efficiency Redefined Through Automation

--

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

--

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

--

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

--

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

--

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

--

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

--

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

by Garrett Davidson - 05:51 - 27 May 2026

2 attachments 2 attachments

cleaning question

Birch Manufacturing team, how many tours of the studio do you usually have in a week? 

First impressions matter a lot with creative directors - an unorganized studio could lose you a repeat client.

We clean for studios around Queen Creek and were curious to know if you would be interested in a complimentary estimate?

Sincerely,
Albert Cummings-Schultz || Viking Cleaning

by "Albert Cummings-Schultz" <a_cummingsschultz@tryvikingcleaning.pro> - 05:37 - 27 May 2026

Re: RFQ

Hi Ivan,

We can square them; quote and lead time are the same. Let me know if that is satisfactory.

Best Regards,

Tony Haynes

Technical Sales Representative

FLODRAULIC

Cell 480.997.2852

Fax 480.921.3272

1150 N. FIESTA BLVD. GILBERT, AZ 85233

ISO 9001:2015 Registered

www.flodraulic.com

*** Important Notice: Send all Inquiries/Orders to our new Customer Service email address SWSales@flodraulicgroup.com***

From: Ivan Arevalo <iarevalo@turnpack.com>
Sent: Wednesday, May 27, 2026 9:49 AM
To: Tony Haynes <thaynes@flodraulicgroup.com>
Cc: Brandon Benavidez <bbenavidez@turnpack.com>; Christopher Berger <cberger@turnpack.com>; Info at Turnpack <info@turnpack.com>
Subject: Re: RFQ

Hi Tony,

Yes, please square those up so we can get the caps on.

I'll get with Chris and Brandon to determine how we want to move forward.

Thanks,

Ivan

On Tue, May 26, 2026 at 10:57 AM Tony Haynes <thaynes@flodraulicgroup.com> wrote:

Hi Ivan,

Here is the Simple Side Module Enclosure quote project number 26359M1 for Turnpack.

We aligned the frames and connectors for the simple side module. Please review

Cost for Kit: $2,243.90 each

Cost for Assembled: $2,809.61 each

5-7 Days

Here is the base module top enclosure quote project number 26358M1 for Turnpack.

*****The bars you want cover caps on are not square on the end so will not go on.

*****If you want them squared, we can square them up and then add the end caps.

Cost for Kit: $1,012.17 each

Cost for Assembled: $1,272.10 each

5-7 Days

Best Regards,

Tony Haynes

Technical Sales Representative

FLODRAULIC

Cell 480.997.2852

Fax 480.921.3272

1150 N. FIESTA BLVD. GILBERT, AZ 85233

ISO 9001:2015 Registered

www.flodraulic.com

*** Important Notice: Send all Inquiries/Orders to our new Customer Service email address SWSales@flodraulicgroup.com***

From: Ivan Arevalo <iarevalo@turnpack.com>
Sent: Thursday, May 21, 2026 5:41 PM
To: Tony Haynes <thaynes@flodraulicgroup.com>
Cc: Brandon Benavidez <bbenavidez@turnpack.com>; Christopher Berger <cberger@turnpack.com>; Info at Turnpack <info@turnpack.com>
Subject: RFQ

Hi Tony,

I've attached two .scene files for some extrusions that we would like pricing on below.

The Base Module Top Enclosure should have the flat edge of the 40x80 3E facing outward. In MAYCAD, it shows up red as an error but we just want the slotted sides to be facing inward toward the enclosure. Additionally, I couldn't get the rubber caps onto the ends of the angled top extrusions in MAYCAD, but we want rubber caps on those.

For the Simple Side Module Enclosure, do not quote the two "hurdles" that connect the back of the enclosure and the front 120x40 extrusion. Those are just placeholders to properly render the mating connection points. We also need additional mounting locations along the front extrusion for better support due to the extended length.

Please reach out with any questions or concerns.

Thank you for your assistance.

Best,

Ivan

by Tony Haynes - 05:21 - 27 May 2026

Re: Jabil 2200Evo

Hi Chris,

Any update on sourcing the spare bond head?

Thanks,

Rod

From: Christopher Berger <cberger@turnpack.com>
Sent: Friday, May 15, 2026 8:01 AM
To: Rod Mapanao <Rod_Mapanao@jabil.com>
Cc: notifications@turnpack.com <notifications@turnpack.com>; Hung Lam <Hung_Lam@jabil.com>; Quyen Chu <Quyen_Chu@jabil.com>; Resty Fonte Familara <RestyFonte_Familara@jabil.com>; lcarrillo@turnpack.com <lcarrillo@turnpack.com>; info@turnpack.com <info@turnpack.com>
Subject: Re: Jabil 2200Evo

EXTERNAL EMAIL: Exercise caution when handling links and attachments.

Hi Rod,

Yes I did miss this. Sorry about that. Let me see if I can get a heated bondhead for you. I will touch base with you later today.

Chris

On Thu, May 14, 2026 at 12:13 PM Rod Mapanao <Rod_Mapanao@jabil.com> wrote:

Hi Chris,

I am following this up, in case you missed this email.

I also added email addresses from our records.

Please send us a quote for Evo+ heated bond head replacement - parts and labor.

Thanks,

ROD MAPANAO
Process Development

MTI

+1.408.750.6278

Jabil MTI
30 Great Oaks Blvd.,
San Jose, CA 95119

From: Rod Mapanao <Rod_Mapanao@Jabil.com>
Sent: Friday, May 8, 2026 5:07 PM
To: Christopher Berger <cberger@turnpack.com>
Cc: Hung Lam <Hung_Lam@jabil.com>; Quyen Chu <Quyen_Chu@jabil.com>; Resty Fonte Familara <RestyFonte_Familara@jabil.com>
Subject: Re: Jabil 2200Evo

Hi Chris,

How are you? It's been a year since the service.

Following up on the spares especially for the heated bond head on Machine#1 SN 950 2219 3998

Ours finally gave up. Do you have a spare and can you replace ours?

Please send us a quote for the spare and installation.

Thanks,

Rod

From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, April 16, 2025 8:12 AM
To: Rod Mapanao <Rod_Mapanao@jabil.com>
Cc: Hung Lam <Hung_Lam@jabil.com>; Quyen Chu <Quyen_Chu@jabil.com>; Resty Fonte Familara <RestyFonte_Familara@jabil.com>
Subject: Re: Jabil 2200Evo

EXTERNAL EMAIL: Exercise caution when handling links and attachments.

Hi Rod,

Attached are the two service reports for last weeks visit. I'll be sending you a quote for the recommended parts later today.

Chris

On Thu, Feb 27, 2025 at 1:02 PM Rod Mapanao <Rod_Mapanao@jabil.com> wrote:

Hi Chris,

We've the machines to another building but the cleanroom is yet to be certified.

While waiting, we could have the machines serviced before moving them again.

Could you please send us a new quotation to diagnose our two 2200Evo.

Thanks and best regards,

Rod

From: Chris Berger <notifications@turnpack.com>
Sent: Thursday, October 10, 2024 3:45 PM
To: Rod Mapanao <rod_mapanao@jabil.com>
Subject: Turnpack, LLC Quotation (Ref SO2441764)

You don't often get email from notifications@turnpack.com. Learn why this is important

EXTERNAL EMAIL: Exercise caution when handling links and attachments.

Hi Rod, Attached is the quote for 1-day service. Let us know if you need anything else? Chris ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏

Hi Rod,

Attached is the quote for 1-day service. Let us know if you need anything else?

Chris

Turnpack, LLC

+1 480-331-1878 | info@turnpack.com | https://www.turnpack.com

Powered by Odoo

--

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

--

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

by Rod Mapanao - 03:31 - 27 May 2026

IEC Supply - Invoice# 11134309

Turnpack


See attached file(s).




Jill Pasquali
IEC Supply
Jill.Pasquali@iecsupply.com

by Jill Pasquali - 03:01 - 27 May 2026

Re: 7D PO 260069 status?

Hi Greg,

Yes we got both orders in production. I will confirm a ship date with you Friday. We are currently battling some technical difficulties with the lathe and are in communication with the Service Engineer. I will keep you posted.

And yes we will replace the bushing, no problem.

Chris

On Wed, May 27, 2026 at 6:02 AM Greg Fraser <greg.fraser@7dkmetrology.com> wrote:

Hi Chris,

Can you please update us on status of PO 260069?

Also, did I mention we have Qty 1 of the 0160216-A Brass bushing with a bad thread. Are you able to add Qty 1 to this PO or next open PO 260099 to replace this bad unit?

Thanks very much,

Greg

GREG FRASER                                   55 Fleming Drive

Lead Hardware Engineer              Units 13-17, Cambridge, ON

(226) 606-3126                                  Canada N1T 2A9

--

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

by Chris Berger - 02:46 - 27 May 2026

lcarrillo@turnpack.com | www.turnpack.com
https://www.turnpack.com/midas-rework/delidder

RE: Company Merger

Dear Lorena and Christopher,

Could you inform us please if those PO’s are in production and you can meet the requested delivery date for both PO’s?

Thank you in advance!

Best regards,

Kate

From: Kate Khomenko
Sent: May 20, 2026 9:44 AM
To: 'info@turnpack.com' <info@turnpack.com>
Cc: Accounting 7D Kinematic Metrology Inc <accounting@7dkmetrology.com>; Greg Fraser <greg.fraser@7dkmetrology.com>; Caroline Tremblay <caroline.tremblay@7dkmetrology.com>; Finances 7D Kinematic Metrology Inc <finances@7dkmetrology.com>
Subject: RE: Company Merger

Hello Lorena,

Currently we have 2 open PO’s, please find attached.

Best regards,

Kate

From: info@turnpack.com <info@turnpack.com>
Sent: May 19, 2026 3:47 PM
To: Kate Khomenko <Kate.Khomenko@7dkmetrology.com>; Accounting 7D Kinematic Metrology Inc <accounting@7dkmetrology.com>; Greg Fraser <greg.fraser@7dkmetrology.com>; Caroline Tremblay <caroline.tremblay@7dkmetrology.com>; Finances 7D Kinematic Metrology Inc <finances@7dkmetrology.com>
Subject: RE: Company Merger

Hello Team, I wanted to follow and confirm POs are being sent to the info@turnpack.com email for processing. Chris said there was an order placed but I am not seeing the PO come through. If so are you able to resend?

From: Kate Khomenko <Kate.Khomenko@7dkmetrology.com>
Sent: Thursday, January 22, 2026 12:06 PM
To: Lorena <info@turnpack.com>; Accounting 7D Kinematic Metrology Inc <accounting@7dkmetrology.com>; Greg Fraser <greg.fraser@7dkmetrology.com>; Caroline Tremblay <caroline.tremblay@7dkmetrology.com>; Finances 7D Kinematic Metrology Inc <finances@7dkmetrology.com>
Subject: RE: Company Merger

Thank you Lorena,

I’ve created a new supplier card in our system based on provided info. I think it is enough for now.

Best regards,

Kate

From: Lorena <info@turnpack.com>
Sent: January 22, 2026 12:29 PM
To: Kate Khomenko <Kate.Khomenko@7dkmetrology.com>; Accounting 7D Kinematic Metrology Inc <accounting@7dkmetrology.com>; Greg Fraser <greg.fraser@7dkmetrology.com>; Caroline Tremblay <caroline.tremblay@7dkmetrology.com>; Finances 7D Kinematic Metrology Inc <finances@7dkmetrology.com>
Subject: RE: Company Merger

Attached is our ACH information.

Phone and address below.

All paperwork goes to info@turnpack.com (purchase orders, shipping requests, account inquiries) this is a team email for faster responses.

Quote/sales requests go to cberger@turnpack.com and preferably CC info@turnpack.com

Let me know if you have any questions.

Lorena Carrillo

Office Manager

Office: 480-331-1878
Line: 781-938-0069

22425 S Scotland Ct, Suite104, Queen Creek, AZ 85142

From: Kate Khomenko <Kate.Khomenko@7dkmetrology.com>
Sent: Thursday, January 22, 2026 10:06 AM
To: Lorena <info@turnpack.com>; Accounting 7D Kinematic Metrology Inc <accounting@7dkmetrology.com>; Greg Fraser <greg.fraser@7dkmetrology.com>; Caroline Tremblay <caroline.tremblay@7dkmetrology.com>; Finances 7D Kinematic Metrology Inc <finances@7dkmetrology.com>
Subject: RE: Company Merger

Hello Lorena,

Please find below our company data to be entered to your database. We would kindly appreciate if you could inform us your new data in the same format as well, since I don’t have full data in my system for Birch Mnf.

General:

Company name: 7D KINEMATIC METROLOGY INC.
Company website: https://7dkmetrology.com/
Tax ID number: 72624 5913 RC0001
Company phone number: 1-519-498-0548 (as our website)

Contacts:

Kate Khomenko, Supply Chain Specialist / 226-929-1392 / kate.khomenko@7dkmetrology.com
Greg Fraser, Production Manager / 226-606-31-26 / greg.fraser@7dkmetrology.com
Jeff Bueckert, Director of Engineering & Operations / jeff.bueckert@7dkmetrology.com
Finance department / Email finances@7dkmetrology.com

Purchasing/Sales terms:

Shipping/Receiving address: 55 Fleming Drive, units 13-17, Cambridge, ON, N1T 2A9
Purchasing/Sales address: (same as shipping/receiving address)
Shipment terms (INCOTERMS): EXW, please use our UPS account 88WE37.
Payment terms: Net 30 day

Best regards,

KATE KHOMENKO 55 Fleming Drive

Supply Chain Specialist Units 13-17, Cambridge, ON

(226) 929-1392 Canada N1T 2A9

From: Lorena <info@turnpack.com>
Sent: December 17, 2025 11:02 AM
To: Accounting 7D Kinematic Metrology Inc <accounting@7dkmetrology.com>; Greg Fraser <greg.fraser@7dkmetrology.com>; Caroline Tremblay <caroline.tremblay@7dkmetrology.com>; Finances 7D Kinematic Metrology Inc <finances@7dkmetrology.com>
Cc: Kate Khomenko <Kate.Khomenko@7dkmetrology.com>
Subject: Company Merger

Hello 7D Team.

I hope this message finds you well.

I am writing to inform you that Birch Manufacturing AZ has been acquired by Turnpack LLC as of December 31, 2025.

Please send any necessary paperwork to establish Turnpack LLC in your database. Kindly note that aside from the company name change, no other modifications are being made.

Additionally, please be aware that Turnpack LLC also acquired Midas Technology as of June 2025.

Please let me know if you need any further information or documentation from our side.

Thank you for your attention to this matter.

Lorena Carrillo

Office Manager

Office: 480-331-1878
Line: 781-938-0069

22425 S Scotland Ct, Suite104, Queen Creek, AZ 85142

lcarrillo@turnpack.com | www.turnpack.com
https://www.turnpack.com/midas-rework/delidder

by "Kate Khomenko" <Kate.Khomenko@7dkmetrology.com> - 02:42 - 27 May 2026

Delivered on Order PO26211758: Drill Bits and Drive Roller

We delivered the drill bits and drive roller on order PO26211758 (received by C.Berger, left at Shipping/Receiving).

by "McMaster-Carr" <la.sales@mcmaster.com> - 02:12 - 27 May 2026

Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Hi Garrett,

Sorry about that. We do check them for flatness and vacuum seal so it would be best if you can ship them back for RCA and we'll fix it. Hope this doesn't delay your project.

Any issues with the Loading Jigs?

Chris

On Wed, May 27, 2026 at 10:34 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:

Hi Chris,

I went through the rest of the delivery and found 3 more that do not slide all the way into the tool (for a total of 4x). Physically they look similar, but may have some slight warpage issues causing these issues. Any ideas on how to fix this? I’m afraid of trying to bend them to fix the warpage. Would you like me to ship them back for you to take a look?

Thanks,

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Garrett Davidson
Sent: Wednesday, May 27, 2026 8:04 AM
To: Christopher Berger <cberger@turnpack.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Sorry, these are two SEPARATE adapters. I’m going through the other adapters now, and will let you know if I see any more issues!

Thanks,

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 27, 2026 7:58 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Hi Garrett,

Thanks for the info. My fault on the partially engraved one, I was supposed to let you know but fell behind. We already have a replacement for that one in queue but I wanted to ship all 20 just in case you needed the full qty right away. Is this the same adapter you are having the issue with on the suction cup or is this a different one?

Chris

On Wed, May 27, 2026 at 7:50 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:

Unsure if this sent or if the full email did not send. I received a bunch of error messages.

Please find the video up in the fileXchange if you need!

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Garrett Davidson
Sent: Tuesday, May 26, 2026 6:28 PM
To: 'Lorena Carrillo' <lcarrillo@turnpack.com>; 'Christopher Berger' <cberger@turnpack.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Hi Chris/Turnpack,

I started opening up the box, and found an issue with one of the adapters:

As I slide the adapter into our tool, it stops here and does not allow us to slide it all the way to the vacuum port. The adapter itself seemed warped when placed on an optical table. I checked 5 more so far from the latest shipment and they all look good! Just this one is unable to slide in. I attached a video of myself trying to push it it and it not going all the way in without me having to physically lift the adapter into place and have a high risk of “confetti-ing” components in waffle packs. Let me know if it doesn’t come through. I also uploaded into our FileXchange system for you to review. Let me know if anyone needs access to this:

One of the 5 that I looked at after this one is missing most of the writing at the bottom of the adapter itself. Not a huge deal as it’s just cosmetic to us, but did want to let you know about it:

I will go through all the rest tomorrow morning and let you know if I encounter any more like this.

Can I send this one back to you to root cause or any ideas how to fix up? I could try to bend it but unsure how brittle the adapter itself is or if I’ll make it worse.

Thanks!

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Garrett Davidson
Sent: Wednesday, May 20, 2026 4:23 PM
To: Lorena Carrillo <lcarrillo@turnpack.com>; 'Christopher Berger' <cberger@turnpack.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Thank you!!

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Lorena Carrillo <lcarrillo@turnpack.com>
Sent: Wednesday, May 20, 2026 4:20 PM
To: 'Christopher Berger' <cberger@turnpack.com>; Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Hello Team, the order has shipped complete today. Here is your tracking number for reference. 872056271057

From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, May 19, 2026 11:18 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Hi Garrett,

We have the adapters back from anodizing but I slightly underestimated the assembly time. We are wrapping up the assembly today and tomorrow will be for engraving and testing and then we'll ship them out tomorrow.

The toolholder jigs are complete and ready to go.

Thanks

Chris

On Mon, May 18, 2026 at 4:29 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:

Hey Chris,

Were you able to ship out those parts? And have a tracking number if possible?

Thanks,

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 13, 2026 7:55 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Garrett,

We experienced a slight delay because a machine was down, but parts are currently at anodizing. We are expediting that process, and then we anticipate two days for post-anodizing assembly & engraving. We might be able to ship it out Saturday, worst case it'll be Monday. I'll keep you posted when the parts come back from anodizing and then I should be able to confirm actual ship date.

Chris

On Wed, May 13, 2026 at 7:39 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:

Hey Chris,

Just checking if you think you’d be able to ship anything this week?

Thanks!

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 4:54 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Perfect. Thanks for confirming

On Tue, Apr 28, 2026 at 4:44 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:

Yeah that’s okay with me!

Thanks,

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 4:23 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Garrett,

Yes. Example image below shows one side machined and the top not machined. If we machine all 4 sides they will all look like the side edge in the image below. Also, we did start with the adapters, once they are ready and in case the jigs are not I will let you know and we can do a partial shipment.

Thanks

Chris

On Tue, Apr 28, 2026 at 4:18 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:

Sorry, what do you mean by “Obscuring them”? would it “fog” the glass or make it not transparent?

The wafer pack adapters are a higher priority for us if possible! But no worries either way.

Thanks,

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 3:44 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Hi Garrett,

Making good progress. As of now it looks like we'll ship the order the week of 05/11. We had a question about the tool holder jigs. We would prefer to machine them on multiple sides but doing so would obscure them. Reason being is that the stock material has significant tolerancing, so facing all sides would ensure greater consistency. Any objections to that?

Chris

On Tue, Apr 28, 2026 at 2:54 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:

Hey Chris,

Hope you are doing well! Do you have an ETA for this order? (PO#3714362)

Thanks,

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Chris Berger <info@turnpack.com>
Sent: Tuesday, April 7, 2026 9:03 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Subject: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Hi Garrett, Attached is the quote for the adapters and loading jigs. Let me know if you need anything else. Chris Christopher Berger Phone: +1 [...] ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏

Sign & Pay Quotation

SO26141038
$ 69,200.00
Expires on 05/07/2026

Hi Garrett,

Attached is the quote for the adapters and loading jigs. Let me know if you need anything else.

Chris

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

Turnpack, LLC

+1 480-331-1878 | info@turnpack.com | https://www.turnpack.com

Turnpack — Efficiency Redefined Through Automation

--

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

--

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

--

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

--

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

--

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

--

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

--

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

by Chris Berger - 01:47 - 27 May 2026

Delivered: "wowstick Mini Electric..."

Delivered: "wowstick Mini Electric..."͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌ ͏ ‌

Your Orders

Your package was delivered!

Delivered today

It was handed directly to a receptionist or someone at a front desk.

Turnpack - QUEEN CREEK, AZ

Order # ‫113-5765356-0253853

Track package

wowstick Mini Electric Screwdriver,3 LED Lights, Electric Screwdriver Cordless Rechargeable Set (23)

Return or replace items in Your Orders.

How was your delivery?

It was great

Not so great

by "Amazon.com" <order-update@amazon.com> - 01:47 - 27 May 2026

Get free 6-month trial of Xero when you join now

Email Template

Xero Know your numbers. Control your cash flow. Online bookkeeping services for small businesses.

Members can try Xero free¹ for 6 months

Join Walmart Business+ for this special online bookkeeping offer.

Upgrade now

A smiling woman with glasses working on a laptop at a desk with shipping boxes and a clothing rack in the background.

Xero helps you control your cash flow

With automated invoicing & online payments, Xero makes it easier to track your budget.

Learn more

Two smiling business owners in striped aprons look at a digital tablet together in a modern café setting.

Online convenience & features that save time

With easy access & real-time reporting, Xero keeps your books while you focus on business.

Discover Xero

¹Offer available to new Xero Customers only. Eligibility & terms apply.

Mobile apps

Questions? Visit our Help Center

Please note that product availability is limited and prices are subject to change. Do not reply to this email. The inbox is not monitored. If you require assistance, please click here for help. Walmart Business protects your security and privacy. We will never ask for personal information (such as passwords or credit card numbers) in an email newsletter. If you receive such a request, please do not respond to the email. Learn more. See our Privacy Policy. This email is a Walmart Business advertisement. If you do not want to receive these email updates, click here to unsubscribe. Walmart Business, 702 SW 8th St, Bentonville, AR 72712 © 2026 Walmart.

by "Walmart Business" <newsletter@em.business.walmart.com> - 01:46 - 27 May 2026

RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Hi Chris,

I went through the rest of the delivery and found 3 more that do not slide all the way into the tool (for a total of 4x). Physically they look similar, but may have some slight warpage issues causing these issues. Any ideas on how to fix this? I’m afraid of trying to bend them to fix the warpage. Would you like me to ship them back for you to take a look?

Thanks,

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Garrett Davidson
Sent: Wednesday, May 27, 2026 8:04 AM
To: Christopher Berger <cberger@turnpack.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Sorry, these are two SEPARATE adapters. I’m going through the other adapters now, and will let you know if I see any more issues!

Thanks,

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 27, 2026 7:58 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Lorena Carrillo <lcarrillo@turnpack.com>; Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Hi Garrett,

Thanks for the info. My fault on the partially engraved one, I was supposed to let you know but fell behind. We already have a replacement for that one in queue but I wanted to ship all 20 just in case you needed the full qty right away. Is this the same adapter you are having the issue with on the suction cup or is this a different one?

Chris

On Wed, May 27, 2026 at 7:50 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:

Unsure if this sent or if the full email did not send. I received a bunch of error messages.

Please find the video up in the fileXchange if you need!

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Garrett Davidson
Sent: Tuesday, May 26, 2026 6:28 PM
To: 'Lorena Carrillo' <lcarrillo@turnpack.com>; 'Christopher Berger' <cberger@turnpack.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Hi Chris/Turnpack,

I started opening up the box, and found an issue with one of the adapters:

As I slide the adapter into our tool, it stops here and does not allow us to slide it all the way to the vacuum port. The adapter itself seemed warped when placed on an optical table. I checked 5 more so far from the latest shipment and they all look good! Just this one is unable to slide in. I attached a video of myself trying to push it it and it not going all the way in without me having to physically lift the adapter into place and have a high risk of “confetti-ing” components in waffle packs. Let me know if it doesn’t come through. I also uploaded into our FileXchange system for you to review. Let me know if anyone needs access to this:

One of the 5 that I looked at after this one is missing most of the writing at the bottom of the adapter itself. Not a huge deal as it’s just cosmetic to us, but did want to let you know about it:

I will go through all the rest tomorrow morning and let you know if I encounter any more like this.

Can I send this one back to you to root cause or any ideas how to fix up? I could try to bend it but unsure how brittle the adapter itself is or if I’ll make it worse.

Thanks!

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Garrett Davidson
Sent: Wednesday, May 20, 2026 4:23 PM
To: Lorena Carrillo <lcarrillo@turnpack.com>; 'Christopher Berger' <cberger@turnpack.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Thank you!!

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Lorena Carrillo <lcarrillo@turnpack.com>
Sent: Wednesday, May 20, 2026 4:20 PM
To: 'Christopher Berger' <cberger@turnpack.com>; Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: 'Turnpack, LLC SO26141038' <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: RE: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Hello Team, the order has shipped complete today. Here is your tracking number for reference. 872056271057

From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, May 19, 2026 11:18 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>; Ryan Chin <Ryan.Chin@spacex.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Hi Garrett,

We have the adapters back from anodizing but I slightly underestimated the assembly time. We are wrapping up the assembly today and tomorrow will be for engraving and testing and then we'll ship them out tomorrow.

The toolholder jigs are complete and ready to go.

Thanks

Chris

On Mon, May 18, 2026 at 4:29 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:

Hey Chris,

Were you able to ship out those parts? And have a tracking number if possible?

Thanks,

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Christopher Berger <cberger@turnpack.com>
Sent: Wednesday, May 13, 2026 7:55 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Garrett,

We experienced a slight delay because a machine was down, but parts are currently at anodizing. We are expediting that process, and then we anticipate two days for post-anodizing assembly & engraving. We might be able to ship it out Saturday, worst case it'll be Monday. I'll keep you posted when the parts come back from anodizing and then I should be able to confirm actual ship date.

Chris

On Wed, May 13, 2026 at 7:39 AM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:

Hey Chris,

Just checking if you think you’d be able to ship anything this week?

Thanks!

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 4:54 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Perfect. Thanks for confirming

On Tue, Apr 28, 2026 at 4:44 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:

Yeah that’s okay with me!

Thanks,

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 4:23 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Garrett,

Yes. Example image below shows one side machined and the top not machined. If we machine all 4 sides they will all look like the side edge in the image below. Also, we did start with the adapters, once they are ready and in case the jigs are not I will let you know and we can do a partial shipment.

Thanks

Chris

On Tue, Apr 28, 2026 at 4:18 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:

Sorry, what do you mean by “Obscuring them”? would it “fog” the glass or make it not transparent?

The wafer pack adapters are a higher priority for us if possible! But no worries either way.

Thanks,

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Christopher Berger <cberger@turnpack.com>
Sent: Tuesday, April 28, 2026 3:44 PM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Cc: Turnpack, LLC SO26141038 <catchall@turnpack.com>
Subject: Re: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Hi Garrett,

Making good progress. As of now it looks like we'll ship the order the week of 05/11. We had a question about the tool holder jigs. We would prefer to machine them on multiple sides but doing so would obscure them. Reason being is that the stock material has significant tolerancing, so facing all sides would ensure greater consistency. Any objections to that?

Chris

On Tue, Apr 28, 2026 at 2:54 PM Garrett Davidson <Garrett.Davidson@spacex.com> wrote:

Hey Chris,

Hope you are doing well! Do you have an ETA for this order? (PO#3714362)

Thanks,

Garrett Davidson

MicroElectronics Hardware Development Engineer

+1 (425) 539 - 1448

From: Chris Berger <info@turnpack.com>
Sent: Tuesday, April 7, 2026 9:03 AM
To: Garrett Davidson <Garrett.Davidson@spacex.com>
Subject: Turnpack, LLC Quotation (Ref SO26141038) - Gelpak Adapters and Loading Jigs

Hi Garrett, Attached is the quote for the adapters and loading jigs. Let me know if you need anything else. Chris Christopher Berger Phone: +1 [...] ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏

Sign & Pay Quotation

SO26141038
$ 69,200.00
Expires on 05/07/2026

Hi Garrett,

Attached is the quote for the adapters and loading jigs. Let me know if you need anything else.

Chris

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

Turnpack, LLC

+1 480-331-1878 | info@turnpack.com | https://www.turnpack.com

Turnpack — Efficiency Redefined Through Automation

--

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

--

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

--

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

--

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

--

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

--

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

by Garrett Davidson - 01:37 - 27 May 2026

SRP eNote: Projected bill

Dear Customer,

Based on your usage through May 26, 2026 for SRP electric account ***-**9-002 at 22425 S SCOTLAND CT SU 104 your June bill is projected to be approximately $470.00. The bill estimate exceeds the threshold you set in My Account.

If you have questions, please contact us at (602) 236-8833, Monday through Friday, 7 a.m.-5 p.m, or by e-mail at commercl@srpnet.com

Thank you for being a valued SRP business customer.

SRP Customer Services

Find us on:

by enotify@srpnet.com - 01:22 - 27 May 2026

Re: RFQ

Hi Tony,

Yes, please square those up so we can get the caps on.

I'll get with Chris and Brandon to determine how we want to move forward.

Thanks,

Ivan

On Tue, May 26, 2026 at 10:57 AM Tony Haynes <thaynes@flodraulicgroup.com> wrote:

Hi Ivan,

Here is the Simple Side Module Enclosure quote project number 26359M1 for Turnpack.

We aligned the frames and connectors for the simple side module. Please review

Cost for Kit: $2,243.90 each

Cost for Assembled: $2,809.61 each

5-7 Days

Here is the base module top enclosure quote project number 26358M1 for Turnpack.

*****The bars you want cover caps on are not square on the end so will not go on.

*****If you want them squared, we can square them up and then add the end caps.

Cost for Kit: $1,012.17 each

Cost for Assembled: $1,272.10 each

5-7 Days

Best Regards,

Tony Haynes

Technical Sales Representative

FLODRAULIC

Cell 480.997.2852

Fax 480.921.3272

1150 N. FIESTA BLVD. GILBERT, AZ 85233

ISO 9001:2015 Registered

www.flodraulic.com

*** Important Notice: Send all Inquiries/Orders to our new Customer Service email address SWSales@flodraulicgroup.com***

From: Ivan Arevalo <iarevalo@turnpack.com>
Sent: Thursday, May 21, 2026 5:41 PM
To: Tony Haynes <thaynes@flodraulicgroup.com>
Cc: Brandon Benavidez <bbenavidez@turnpack.com>; Christopher Berger <cberger@turnpack.com>; Info at Turnpack <info@turnpack.com>
Subject: RFQ

Hi Tony,

I've attached two .scene files for some extrusions that we would like pricing on below.

The Base Module Top Enclosure should have the flat edge of the 40x80 3E facing outward. In MAYCAD, it shows up red as an error but we just want the slotted sides to be facing inward toward the enclosure. Additionally, I couldn't get the rubber caps onto the ends of the angled top extrusions in MAYCAD, but we want rubber caps on those.

For the Simple Side Module Enclosure, do not quote the two "hurdles" that connect the back of the enclosure and the front 120x40 extrusion. Those are just placeholders to properly render the mating connection points. We also need additional mounting locations along the front extrusion for better support due to the extended length.

Please reach out with any questions or concerns.

Thank you for your assistance.

Best,

Ivan

by Ivan Arevalo - 12:53 - 27 May 2026

Apply today for your pre-qualified loan through Quickbooks

Intuit

	QuickBooks Term Loan

Apply for your up to $100,000 loan

Congratulations! You have been pre-qualified for up to $100,000.¹ Apply now to access funds in days.² Offer ends 6/1/2026.

Learn more

Why choose QuickBooks Term Loan?

Seamless experience

Get competitive rates and fast funding. Apply right from your QuickBooks account.

Smart business funding

Know the total cost of financing up front. No origination fees, prepayment penalties, or hidden charges.³

Less stress, more capital

Applying for QuickBooks Term Loan won't affect your personal credit score.

Learn more

View on web

QuickBooks Term Loan ("Term Loan") is issued by WebBank. QuickBooks Capital is licensed as Intuit Financing Inc. (NMLS #1136148), a subsidiary of Intuit Inc.

Subject to eligibility

1.

Pre-qualified: Pre-qualified means you have been selected to receive this offer based on meeting certain criteria determined by the lender. To take advantage of this offer, submit an application, which will be reviewed for creditworthiness and verification of additional information prior to a final credit decision. This offer is not guaranteed. Program loan amounts may range from $[x] to $[y]. Final offer may be affected if you apply for QuickBooks Line of Credit first.

2.

Fast Funding: Loans are typically deposited within 1-2 business days. Actual funding time can vary depending on third party processing time.

3.

No fees: Interest will apply. Rates vary and depend on applicant's credit profile and other factors.

ELM ID: 3802-02

This message was sent to info@turnpack.com, as an Intuit customer, consistent with your email preferences. If you have chosen not to receive marketing messages, you will continue to receive business communications about your selected Intuit product(s), which may either affect your service or software, your account, or which may be legally required.

Unsubscribe

|

Security

|

Privacy statement

by "Intuit QuickBooks" <intuit@eq.intuit.com> - 12:12 - 27 May 2026

RE: Turnpack, LLC Invoice (Ref INV/2026/02/0003) ACCOUNT ON CREDIT HOLD

Hello,

Payment was mailed to 22425 S Scotland Court Suite 104 Queen Creek, AZ 85142. I do not have an image of the check as it has not been cashed through the bank.

Best regards,

Sarah Rousseau

Email: S.Rousseau@us.vigophotonics.com
Phone: 772-223-6670

From: info@turnpack.com <info@turnpack.com>
Sent: Wednesday, May 27, 2026 11:05 AM
To: IRassoc IRA (Shared) <IRassoc@us.vigophotonics.com>
Subject: RE: Turnpack, LLC Invoice (Ref INV/2026/02/0003) ACCOUNT ON CREDIT HOLD

Check has not been received. Can you please send an image of the check and confirm mailing address?

From: IRassoc IRA (Shared) <IRassoc@us.vigophotonics.com>
Sent: Wednesday, May 27, 2026 7:00 AM
To: info@turnpack.com
Subject: RE: Turnpack, LLC Invoice (Ref INV/2026/02/0003) ACCOUNT ON CREDIT HOLD

Hello,

Check #1014 was mailed on 05/07/2026.

Best regards,

Sarah Rousseau

Email: S.Rousseau@us.vigophotonics.com
Phone: 772-223-6670

From: info@turnpack.com <info@turnpack.com>
Sent: Friday, May 22, 2026 8:56 PM
To: IRassoc IRA (Shared) <irassoc@irassociates.com>
Subject: RE: Turnpack, LLC Invoice (Ref INV/2026/02/0003) ACCOUNT ON CREDIT HOLD

This invoice is still not paid as of todays date. I need payment status right away.

From: info@turnpack.com <info@turnpack.com>
Sent: Monday, April 6, 2026 2:28 PM
To: irassoc@irassociates.com
Subject: RE: Turnpack, LLC Invoice (Ref INV/2026/02/0003) ACCOUNT ON CREDIT HOLD

please see attached per your request.

From: IRassoc IRA (Shared) <info@turnpack.com>
Sent: Monday, April 6, 2026 12:37 PM
To: Info Inbox <info@turnpack.com>
Subject: RE: Turnpack, LLC Invoice (Ref INV/2026/02/0003) ACCOUNT ON CREDIT HOLD

Could you please forward the original email as I am not seeing it? If there is an issue with my email I will need to forward to our IT department.

Best regards,

Sarah Rousseau

Email: S.Rousseau@us.vigophotonics.com
Phone: 772-223-6670

From: info@turnpack.com <info@turnpack.com>
Sent: Monday, April 6, 2026 2:50 PM
To: IRassoc IRA (Shared) <IRassoc@us.vigophotonics.com>
Subject: RE: Turnpack, LLC Invoice (Ref INV/2026/02/0003) ACCOUNT ON CREDIT HOLD

It was sent to this same address as always.

From: IRassoc IRA (Shared) <IRassoc@us.vigophotonics.com>
Sent: Friday, April 3, 2026 5:29 AM
To: Turnpack, LLC INV/2026/02/0003 (25-11837) <catchall@turnpack.com>
Subject: RE: Turnpack, LLC Invoice (Ref INV/2026/02/0003) ACCOUNT ON CREDIT HOLD

Hi Lorena,

It appears that this is our first time receiving this invoice, could you please forward the original invoice email as I would like to confirm the email address is correct. Thank you.

Best regards,

Sarah Rousseau

Email: S.Rousseau@us.vigophotonics.com
Phone: 772-223-6670

3 attachments 3 attachments

From: Lorena Carrillo <info@turnpack.com>
Sent: Thursday, April 2, 2026 5:40 PM
To: IRassoc IRA (Shared) <irassoc@irassociates.com>
Subject: Turnpack, LLC Invoice (Ref INV/2026/02/0003) ACCOUNT ON CREDIT HOLD

Dear Accounts Payable (Infrared Associates), Please see attached invoice INV/2026/02/0003 (with reference: SO2534933) amounting in $ 146.26 from [...] ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏

View Invoice

INV/2026/02/0003
$ 146.26 due 3/7/26

Dear Accounts Payable (Infrared Associates),

Please see attached invoice INV/2026/02/0003 (with reference: SO2534933) amounting in $ 146.26 from Turnpack, LLC. Please remit payment at your earliest convenience.

Please use the following communication for your payment: INV/2026/02/0003.

If you have received this email in error, please reply with the proper contact.
Please reply to this email or resend an email to info@turnpack.com, with any questions, comments, or concerns regarding your order.

Your prompt payment is greatly appreciated. To avoid any interest or penalties on invoices over the stated payment terms, please remit payment by date stated on your invoice.
If payment has not been received by the 5th late business day an APR of 7.75% will be charged daily until payment in full has been received. Client is responsible for all collection costs deemed reasonable by Turnpack.

NOTE: while ACH is our preferred payment method we do accepts checks. Please make check payable to: "Turnpack LLC" and mail to the new address below. Credit card is accepted upon request with a 3.6% fee.

Please note change of Address:
22425 S Scotland Ct
Suite 104
Queen Creek, AZ 85142

Turnpack, LLC

+1 480-331-1878 | info@turnpack.com | https://www.turnpack.com

Turnpack — Efficiency Redefined Through Automation

by "IRassoc IRA (Shared)" <IRassoc@us.vigophotonics.com> - 11:56 - 27 May 2026

RE: Turnpack, LLC Order (Ref SO26131037)

Chris,

This PO 260069 is a current, open order with your company. We sent this PO in on 4/6/2026. This is not a new PO to you.

I am asking when you will be done with it and deliver these parts to us…..lol?

Thanks,

Greg

GREG FRASER 55 Fleming Drive

Lead Hardware Engineer Units 13-17, Cambridge, ON

(226) 606-3126 Canada N1T 2A9

From: Chris Berger <info@turnpack.com>
Sent: Wednesday, May 27, 2026 11:13 AM
To: Greg Fraser <greg.fraser@7dkmetrology.com>
Subject: Turnpack, LLC Order (Ref SO26131037)

Hello, Your order SO26131037 amounting in $ 6,683.31 has been confirmed. Thank you for your trust! Do not hesitate to contact us if you have any [...] ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏ ͏

View Sales Order

SO26131037
$ 6,683.31

Hello,

Your order SO26131037 amounting in $ 6,683.31 has been confirmed.
Thank you for your trust!

Do not hesitate to contact us if you have any questions.

Christopher Berger

Phone: +1 (480) 331-1878

Cell: +1 (480) 273-4686

cberger@turnpack.com | www.turnpack.com

Turnpack, LLC

+1 480-331-1878 | info@turnpack.com | https://www.turnpack.com

Turnpack — Efficiency Redefined Through Automation

by Greg Fraser - 11:32 - 27 May 2026